Deck 8: Shop Tools

Question 1

A torque wrench is used to tighten a fastener a prescribed amount.

Answer 1

True

Question 2

When a nut or bolt is extremely tight, a ____ is used so that the teeth in the ratchet head are not damaged.

A)socket
B)breaker bar
C)ratchet
D)clutch

Answer 2

B

Question 3

The flare-nut wrench has an opening on one of its sides that allows it to slip over a fuel line.

Answer 3

True

Question 4

____________________ are used to remove or install pressed-fit parts on shafts, like gears, bushings, and bearings.

Question 5

A wrench head that has been adapted so that it can be used with a ratchet and extension is MOST-Likely referred to as a(n):

A)crowfoot socket.
B)impact socket.
C)wobble socket.
D)swivel socket.

Question 6

Which of the following socket drives is LEAST-Likely to be used on an automobile?

A)1/4"
B)3/8"
C)1/2"
D)3/4"

Question 7

While discussing air compressors, Technician A says that air pressure should be regulated to 40 psi to get the best performance and reliability from air tools. Technician B says that air pressure should be regulated at 60 psi.

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 8

A hammer is used to secure a bearing to a shaft or hold it inside of a housing.

Question 9

A favorite among professional technicians is the combination wrench, which includes a box wrench and an open-end wrench on one end or the other.

Question 10

Most automotive technicians own their own set of ____________________, including items like sockets, wrenches, and screwdrivers.

Question 11

While having a discussion about hammers, Technician A says that pounding on a chisel with too large a hammer can cause chips in the chisel head. Technician B says that a hammer head should be no more than 3.8" larger in diameter than the head of the punch or chisel. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 12

A #1 Phillips head is larger than a #2.

Question 13

Which of the following is LEAST-Likely to be a type of pliers?

A)Rib joint
B)Needle nose
C)Allen head
D)Slip-joint utility

Question 14

When removing a nut from a long stud, the MOST-Likely tool used to provide clearance is the:

A)spark plug.
B)screwdriver.
C)deep socket.
D)wrench.

Question 15

Each of the following represent common sizes of extensions EXCEPT:

A)2"
B)3"
C)6"
D)10"

Question 16

A(n) ____ is sometimes used to loosen or tighten parts such as muffler clamps or steering linkage tie-rod end clamps.

A)crescent wrench
B)ratcheting box wrench
C)Allen wrench
D)adjustable wrench

Question 17

A(n) ____________________ is a hex tool used to turn setscrews and capscrews.

Question 18

A(n) ____________________ is similar to a Phillips head, but it has little wings on the inside that provide a slightly better grip and hold onto fasteners for easier assembly work.

Question 19

All of the following are components of a simple planetary gear EXCEPT:

A)the impact socket.
B)the sun gear.
C)the planetary carrier or cage.
D)the three pinion gears.

Question 20

____________________ are pieces of metal that come off the workpiece during filing.

Question 21

What is the difference between a ratcheting box wrench and an adjustable wrench?

Question 22

Name four precautions you should take when using a puller.

Question 23

Provide four tips on proper hacksaw usage.

Question 24

What is the difference between a clutch head and a Scrulox screwdriver?

Question 25

Why is it not advisable to use a Reed and Prince on automotive screws?