Deck 16: Structural Glass Service

Question 1

____ is used for side and rear window glass but rarely for windshields.

A) Laminated plate glass
B) Tempered glass
C) Antilacerative glass
D) Conventional glass

Answer 1

B

Question 2

All of the following are types of glass EXCEPT:

A) tempered
B) laminated plate
C) molded
D) encapsulated

Answer 2

C

Question 3

If too much sealant is applied, excessive moldout will occur.

Answer 3

False

Question 4

Cracks that develop in the outer edge of the glass are sometimes caused by low or high spots or poor ____________ in the pinch weld flange.

A) adhesive application
B) spot welds
C) adhesive removal
D) grinding

Question 5

Electric adhesive cutters plug into 220-volt outlets or use rechargeable battery power to produce a vibrating action that cuts the adhesive around the glass.

Question 6

____ is used in the front windshield only and provides added protection against shattering and cuts during impact.

A) Laminated plate glass
B) Tempered glass
C) Antilacerative glass
D) Conventional glass

Question 7

Adhesive-bonded windshields increase the overall rigidity of the vehicle, minimizing body twist and helping to keep the glass in place during a collision.

Question 8

Most urethane adhesives cannot be installed during cold or freezing temperatures.

Question 9

When using the full cut-out method, what should be used to remove rust from the pinch weld flange?

A) Paint stripper
B) Scrapper
C) #180 grit sandpaper
D) #80 grit sanding disc

Question 10

A heat gun can be used to soften up the adhesive when using a steel wire to remove the glass

Question 11

Windshields and rear windows are usually secured in place by rubber weatherstripping or by an adhesive.

Question 12

What type of technicians are frequently required to service vehicle glass.

A) detail
B) refinish
C) structural
D) helper

Question 13

What accessory is likely to be installed in or around the windshield glass.

A) Rain sensor
B) Wiper switch
C) Dome light
D) Rear defroster

Question 14

Laminated glass can shatter into thousands of tiny fragments.

Question 15

When laminated glass is broken, the plastic material helps to hold the shattered glass in place and prevent it from causing injury.

Question 16

Special tools are not required for wiper arm removal.

Question 17

The ____ method of windshield replacement utilizes the old adhesive as a base for the application of new adhesive.

A) adhesive cutout
B) rubber cutout
C) full cutout
D) partial cutout

Question 18

To prevent water leaks through tiny pin holes or pits in spot welds, what type of welder should be used?

A) squeeze type resistance
B) MIG
C) electric arc
D) TIG

Question 19

____ is used to make all windshields and some side glass.

A) Laminated plate glass
B) Tempered glass
C) Antilacerative glass
D) Conventional glass

Question 20

Stationary glass adhesives are much stronger than other adhesives and sealants.

Question 21

A(n) _________________________ is often needed to reach under the molding to release the clip from under the molding lip.

Question 22

______________________________ use shop air pressure and a vibrating action to help cut the adhesive around the glass.

Question 23

What is the partial cutout method?

Question 24

Describe the dangers of improper installation of windshields.

Question 25

If the original glass is to be reinstalled, what should be used to remove all traces of adhesive from the glass?

A) Denatured alcohol
B) Glass cleaner
C) #400 grit sandpaper
D) Plastic scraper

Question 26

Adhesive can be softened by using?

A) solvent
B) a pneumatic knife
C) a heat gun
D) adhesive remover

Question 27

_________________________ moldings, the windshield wipers, cowl grille, and related parts often must be removed before the windshield will come out.

Question 28

While having a discussion, Technician A says stationary glass isn't intended to help contain passengers during a collision.Technician B says stationary glass strengthens the body structure.Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 29

Technician A says that windshield removal requires the removal of interior and exterior moldings.Technician B says that tools are not needed to remove the molding.

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 30

All of the following can be used to cut adhesive EXCEPT:

A) hot knife
B) serrated knife
C) pneumatic knife
D) steel wire

Question 31

The that LEAST-Likely to affect adhesive curing time is:

A) adhesive type
B) humidity
C) temperature
D) glass type

Question 32

While having a discussion, Technician A says that outside glass specialty shops are often hired to install windshields and back glass.Technician B says that windshields and rear windows are usually secured in place by rubber weatherstripping or by an adhesive.Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 33

______________________________ consists of two thin sheets of glass with a thin layer of clear plastic (vinyl) between them.

Question 34

What should be used to check the windshield installation for leaks.

A) water hose
B) direct flowing water
C) fine water spray
D) low pressure air

Question 35

____________________ is a transparent substance manufactured by heating a mixture of sand, soda (sodium carbonate), limestone, and other materials to a temperature of about 2,400°F (1,300°C).

Question 36

Describe one of the biggest things too always lookout for when doing the full cutout method.

Question 37

Which of the following statements is LEAST-Likely true?

A) Removing rear and quarter windows will not prevent hard tape lines around painted panels.
B) Quarter windows can be secured with rubber molding, adhesive, fasteners, or a combination of methods.
C) Some shops choose not to remove the rear and quarter windows and use certain types of tape to mask them off.
D) The quarter window can be removed after removing interior and exterior moldings.

Question 38

Which of the following statements is LEAST-Likely true?

A) If the wiper blades must be replaced, disengage them from the wiper arm.
B) When installing windshield wiper arms, make sure they are adjusted properly.
C) If a nut is used, a cover over the nut must be pivoted upward or popped off.
D) Engaging the arm into different teeth on the drive shaft will not change the adjustment.

Question 39

Describe urethane adhesive defects and failures.

Question 40

What is one of the first steps in glass service?