Deck 2: Hand Power Tools

Question 1

The size of a drill is determined by the capacity of the chuck.

Answer 1

True

Question 2

____ drills can deliver as much as 50,000 hammer blows per minute on the drill point.

A) Geared head
B) Hammer
C) Radial arm
D) Mill

Answer 2

B

Question 3

Blades for a Sawzall are available for cutting many materials, including _____ .

A) vinyl flooring
B) sheetrock
C) fiberglass
D) Plexiglas®

Answer 3

C

Question 4

Hammer drills are best suited drilling into wood.

Question 5

The saber saw is sometimes called a ____.

A) compass saw
B) wallboard saw
C) jigsaw
D) keyhole saw

Question 6

A light-duty specialized type of router is called a ____ trimmer.

A) form
B) shape
C) layered
D) laminate

Question 7

The size of a portable electric circular saw is determined by the diameter of the blade.

Question 8

The ____ saw, sometimes called a Sawzall, is used primarily for roughing in work.

A) chamfer
B) reciprocating
C) transverse
D) lateral

Question 9

Faster speeds are used for drilling smaller holes and driving fasteners.

Question 10

Cordless circular saws cannot cut dimension lumber.

Question 11

The reciprocating saw is used in a manner similar to the _____ .

A) saber saw
B) Skilsaw
C) circular saw
D) orbital saw

Question 12

____ are used extensively for fastening gypsum board to walls and ceilings with screws.

A) Screw guns
B) Caulking guns
C) Blowguns
D) Heat guns

Question 13

When loosing the bolt holding a circular saw blade, it should be rotated opposite to the normal rotation of the blade.

Question 14

Brad nailers are used to fasten thin materials.

Question 15

With a long blade, the _____ can be used to cut flush with a floor or along the side of a stud.

A) jigsaw
B) Saber saw
C) circular saw
D) reciprocating saw

Question 16

The guard of a circular saw should never be retracted by hand.

Question 17

Sometimes called the ____, the portable electric circular saw is used often by the carpenter.

A) Skilsaw
B) hacksaw
C) ripsaw
D) coping saw

Question 18

Portable power planes have an adjustable ____ that allows planing square, beveled edges to 45 degrees, or chamfers.

A) chuck
B) blade
C) fence
D) bit

Question 19

A chamfer is a small bevel on the edge of stock.

Question 20

A compound miter cut is a combination of a bevel and miter cuts.

Question 21

The heavy-duty ____ drives smooth-shank, headed nails up to 3 1 / 4 inches, ring-shank nails up to 2 3 / 8 inches, and screw shank nails up to 3 inches.

A) finish nailer
B) brad nailer
C) framing gun
D) roofing nailer

Question 22

____-actuated drivers are used to drive specially designed pins into masonry or steel.

A) Pneumatic
B) Powder
C) Battery
D) Hand

Question 23

The portable ____ sander is used frequently for sanding cabinetwork and interior finish.

A) disc
B) belt
C) drum
D) stroke

Question 24

Finishing sanders either have a(n) ____ motion, an oscillating (straight back-and-forth) motion, or a combination of motions controlled by a switch.

A) orbital
B) hyperbolic
C) parabolic
D) lateral

Question 25

__________ cutting is done by rotating a tool base so the spinning blade cuts into the material.

Question 26

Pneumatic staplers and nailers are commonly called ____.

A) tubes
B) rods
C) blasters
D) guns

Question 27

For boring holes in rough work, the speed bore or _____ is commonly used.

Question 28

The material removed when cutting with saw blades creates a space called the __________.