Deck 24: Refinishing Equipment Technology

Question 1

ASE-Style Multiple Choice ____ breaks the liquid material into a fine mist spray of tiny, uniform droplets.

A)Crossflow
B)Atomization
C)Arcing
D)Heeling

Answer 1

B

Question 2

Low spray gun pressure results in excessive paint loss through overspray and poor flow due to high solvent evaporation before the paint reaches the surface.

Answer 2

False

Question 3

ASE-Style Multiple Choice ____ ensures full, even coverage without applying too much paint at once.

A)Spray stroke
B)Spray overlap
C)Viscosity
D)High-transfer efficiency

Answer 3

B

Question 4

Viscosity of sprayable materials is measured in minutes.

Question 5

Improper viscosity can cause excessive overspray, increased booth maintenance, runs or sags, pebble-dry finishes, and color mismatches.

Question 6

ASE-Style Multiple Choice You set the size of the spray pattern using the ____.

A)air valve
B)pattern control knob
C)fluid control knob
D)stroke

Question 7

A spray gun normally has two adjustment knobs: fluid adjustment and pattern adjustment.

Question 8

ASE-Style Multiple Choice ____ involves keeping constant airflow out of the nozzle and only triggering paint flow when depositing paint materials on the body.

A)Spray gun triggering
B)Atomization
C)Heeling
D)Arcing

Question 9

If spray gun distance is too close, the high velocity of the spraying air tends to ripple the wet paint film.

Question 10

A spray gun breaks the liquid sealer, primer, paint, and so on into a fine mist and forces it onto the surfaces of the vehicle.

Question 11

ASE-Style Multiple Choice All of the following represent the basic equipment needed to operate a spray gun EXCEPT:

A)an air hose
B)a sensor
C)an air compressor
D)a filter

Question 12

High-volume efficiency means that more of the material leaving the gun stays on the surface being refinished.

Question 13

Wasteful overspray is caused by a failure to trigger a spray gun before and after each stroke.

Question 14

ASE-Style Multiple Choice Which of the following variables LEAST-Likely contributes to the quality of a spray finish?

A)An agitation paddle
B)Cleanliness
C)Compressed air
D)Light

Question 15

ASE-Style Multiple Choice ____ use airflow through the gun head to form a siphoning action (negative pressure)in the cup that pulls the refinish liquid through the gun body and into the airstream.

A)Suction spray guns
B)Gravity-fed spray guns
C)Pressure-fed spray guns
D)Fluid control knobs

Question 16

ASE-Style Multiple Choice A ____ checks the operation of the spray gun on a piece of paper.

A)pattern test
B)fluid test
C)viscosity test
D)spray pattern test

Question 17

Spray gun feed refers to how the liquid material is fed into the gun body.

Question 18

A gravity-fed gun is more likely to leak and drip paint when spraying.

Question 19

ASE-Style Multiple Choice All of the following are located in an air cap EXCEPT:

A)the center orifice
B)the side orifice
C)the auxiliary orifice
D)the trigger

Question 20

ASE-Style Multiple Choice ____ involves keeping the gun aimed so that an even film of paint deposits on the body surface.

A)Spray gun triggering
B)Spray overlap
C)Spray gun direction
D)Atomization

Question 21

ASE-Style Multiple Choice While having a discussion about air spray guns, Technician A says that one possible cause of the spray pattern being top or bottom heavy is that the horn holes could be partially plugged. Technician B says that one possible cause could be that the atomizing pressure is too low. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 22

When using a spray gun, how do you avoid air supply and painting problems?

Question 23

ASE-Style Multiple Choice The tool that is used to weigh paint ingredients when mixing the paint to match the original color or tone is MOST-Likely the:

A)strainer
B)spray booth
C)paint scale
D)paint scale

Question 24

ASE-Style Multiple Choice ____ is a gun handling problem that occurs when the spray gun is not moved parallel with the surface.

A)Arcing
B)Atomization
C)Heeling
D)Overspray

Question 25

How do you keep dirt from becoming a problem in a finish during body repairs?

Question 26

What is the difference between masking paper and masking tape?

Question 27

ASE-Style Multiple Choice Which of the following is LEAST-Likely a type of spray gun?

A)Airless spray gun
B)Electrostatic
C)Airbrush
D)Trigger

Question 28

_________________________ is how fast you move the gun sideways over the surface.

Question 29

______________________________ use air pressure inside the paint cup (pot)or tank to force the material out of the gun.

Question 30

____________________ is the measurement of thickness, fluidity, or flow resistance of a liquid.

Question 31

A(n)_________________________ and hose on the siphon spray gun allow atmospheric pressure to enter the cup.

Question 32

ASE-Style Multiple Choice The ____ of more sophisticated paint shops have permanent infrared or sodium quartz units for the forced drying of paint, particularly enamels.

A)suction spray guns
B)drying rooms
C)spray gun cleaning tank
D)suspension systems

Question 33

List the four air makeup systems in use today.

Question 34

ASE-Style Multiple Choice A ____ indicates how much airflow is going through a paint booth.

A)booth manometer
B)thermostat
C)drive shaft
D)transaxle

Question 35

_________________________ refers to the hand motion used to move the gun while spraying.

Question 36

ASE-Style Multiple Choice ____ occurs when the painter allows the gun to tilt.

A)Arcing
B)Spray overlap
C)Dry filtration
D)Heeling

Question 37

ASE-Style Multiple Choice While having a discussion, Technician A says that cotton clothing is perhaps the greatest source of contamination and should never be worn in a spray booth. Technician B says that lint-free paint suits, rubber form-fitting gloves, a dirt-free head cover, and the appropriate respirator should be worn inside the booth. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 38

ASE-Style Multiple Choice The tool that is used to suspend or secure individual components or small parts for spray painting is MOST-Likely the:

A)paint hanger
B)spray booth
C)strainer
D)paint shaker

Question 39

ASE-Style Multiple Choice ____ is compatible with paint and will not contaminate the gun.

A)Jounce
B)Camber
C)Spray gun oil
D)Caster

Question 40

What information should you bear in mind when evaluating a spray pattern test?