Deck 3: Automotive Tools and Equipment Tools and Equipment Usage

Question 1

Sliding T-handles can be used to drive a socket.

Answer 1

True

Question 2

Combination pliers are the least common type of pliers used.

Answer 2

False

Question 3

What statement is true concerning service information?

A)Service information is only available in electronic form.
B)Some service information may be VIN specific.
C)DTCs are part of the technical service bulletins.
D)Service information is always generic.

Answer 3

B

Question 4

Which type of wrench goes entirely around a nut or bold head?

A)Box-end
B)Gear
C)Open-end
D)Socket

Question 5

Offset screwdrivers are designed to work in tight spaces.

Question 6

What statement is true concerning lifts?

A)Automotive lifts make work easier.
B)Double post lifts use one hydraulic cylinder.
C)Scissors lifts are typically older lifts.
D)Single post lifts are designed for brake work.

Question 7

Two technicians are discussing vacuum testers. Technician A says that vacuum testers are not designed to diagnose engines. Technician B says that vacuum testers will not work on a computer controlled vehicle. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 8

Wheel blocks should always be placed in front and behind a tire.

Question 9

The size of a wrench is determined by the nut or bolt head it fits on.

Question 10

Two technicians are discussing adjustable wrenches. Technician A says that the length of the wrench handle does not determine how wide the jaws open. Technician B says that adjustable wrenches are sized by the wrench handle. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 11

Two technicians are discussing multimeters. Technician A says that multimeters can test almost any circuit on a car. Technician B says that multimeters should be high-impedance. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 12

Two technicians are discussing automotive jacks. Technician A says that floor jacks are the most common jack found in automotive shops. Technician B says that most floor jacks in shops are rated between six and eight tons. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 13

Two technicians are discussing computerized service information. Technician A says that paper manuals are much less expensive to maintain. Technician B says that most paper service manuals have been replaced by computerized data systems. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 14

A reamer is used when a hole must have a precision fit.

Question 15

Box-end wrenches have less chance of slipping off than an open-end wrench.

Question 16

Multimeters _____.

A)can only check the starter circuit
B)for automobiles should be high impedance
C)all require manual ranging
D)of high impedance are typically rated less than 10 megaohms

Question 17

Two technicians are discussing wrenches. Technician A says that fingers should be wrapped around the handle of an open-end wrench if the wrench needs to be pushed toward an obstruction. Technician B says that an open-end wrench holds a bolt head better than a box-end wrench. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 18

Adjustable wrenches are as strong as standard open-end wrenches.

Question 19

Vise grip pliers are compound-lever pliers that can be locked to the part.

Question 20

Rubber mallets are used for driving pilot pins.

Question 21

Two technicians are discussing offset screwdrivers. Technician A says that offset screwdrivers are for working in tight spaces. Technician B says that offset screwdrivers come in a variety of sizes. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 22

List the uses for a file.

Question 23

Two technicians are discussing screwdrivers. Technician A says that the standard screwdriver is the most common screwdriver used. Technician B says that Phillips screwdrivers have a recessed-type head. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 24

Which type of pliers is useful for locking onto an object?

A)Combination
B)Needle nose
C)Vise grip
D)Dykes

Question 25

Describe taps and dies.

Question 26

What is a combination wrench?

Question 27

What type of pliers should be used to cut wire?

Question 28

Describe the operation of an impact wrench.

Question 29

What is the shape of the end of a torx-type screwdriver?

Question 30

What type of hammer should be used to drive pilot pins?

Question 31

What is one of the most common hammers used in an automotive shop?

Question 32

What is the most common recessed-head screwdriver?

Question 33

What type of screwdriver is used when the screw head has one slot?

Question 34

Describe when a reamer should be used on a hole.

Question 35

How many points can a box-end wrench head have?

Question 36

What is true of torque wrenches?

A)Torque wrenches are used to final-tighten bolts and nuts.
B)Torque wrenches are designed to loosen bolts or nuts.
C)Torque wrenches are factory set and never need adjustment.
D)Torque wrenches automatically stop when they break over the set torque.

Question 37

Describe the difference between a starter punch and a pin punch.

Question 38

Two technicians are discussing pliers. Technician A says that pliers are typically used to loosen nuts and bolts. Technician B says that pliers act as an extension of a technician's fingers. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 39

What type of pliers can be locked onto an item?

Question 40

How many sides does an Allen wrench have?