Deck 3: Hand Tools

Question 1

____________________ pliers have a mechanism which firmly locks the jaws closed on an object.

Answer 1

Locking

Question 2

Technician A says a standard screwdriver should not be used as a chisel. Technician B says a ball peen hammer and chisel are used to shear off rusted bolt heads. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Answer 2

C

Question 3

A ____________________ hammer should be used to drive a chisel.

Answer 3

Ball Peen

Question 4

Body files are used to remove creases in sheet metal.

Question 5

Technician A says the head of a flare nut wrench is missing 2 of the six sides and should be used to loosen fuel and brake lines. Technician B says a box-end wrench will provide the best grip for removing fuel and brake lines. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 6

A box-end wrench provides the best grip on a hex head fastener.

Question 7

Technician A says a box-end wrench provides the best grip on a hex head fastener. Technician B says an open-end wrench provides the best grip on a square head fastener. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 8

Technician A says a pozi drive screw driver is merely another name for a phillips screw driver. Technician B says a Pozidrive screwdriver should be used to remove a clutch head screw. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 9

Technician A says an open-ended wrench may slip if too much force is applied. Technician B says a locking plier will have more holding power than a box-end wrench when loosening an undamaged nut. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 10

Technician A says a body file is used to remove a crease in sheet metal. Technician A says a ball peen hammer is an essential tool for forming the final contour on sheet metal. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 11

A bumping hammer should be used to shape contours of damaged ____________________ panels.

Question 12

A ____________________ is used to cut external threads.

Question 13

A spoon is designed to distribute the striking force over a wide area.

Question 14

Technician A says adjustable pliers can be used to remove clips and wires. Technician B says a clutch screwdriver will have greater turning power and less slippage than a standard screwdriver. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 15

A standard screwdriver can also be used as a chisel.

Question 16

Which is the best hammer to use for initial straightening on dented panels?

A) Finishing hammer
B) Dead blow hammer
C) Ball peen hammer
D) Dinging hammer

Question 17

When using a ball peen hammer and chisel, ____________________ glasses must be worn.

Question 18

Locking pliers will have more holding power than a box-end wrench when used for loosening an undamaged nut.

Question 19

Technician A says holes should not be drilled to provide access to the damage when using a pry bar. Technician B says a spoon is designed to distribute the striking force over a wide area. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 20

Which one of the following should be used to cut internal threads?

A) Tap
B) Die
C) Allen wrench
D) Torx driver

Question 21

How does a shrinking hammer face differ from a finishing hammer's face?

Question 22

Which is better: a 6 point or a 12 point socket?

Question 23

Explain the differing uses of a pick hammer and a finishing hammer.

Question 24

What is a surform file used for?

Question 25

How should a pick hammer be maintained?