Deck 9: Trim and Hardware

Question 1

SAE stands for Society of American Electricians.

Answer 1

False

Question 2

Pop rivets are also referred to as blind rivets.

Answer 2

True

Question 3

For correct reinstallation, it is vital to properly ____________________ and store parts and fasteners when removed.

Answer 3

Label

Question 4

Technician A says that appliqués can be either masked over or removed and glued back on. Technician B says that an eraser disk should be used at approximately 8000 to 10000 RPM's. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 5

Technician A says that adhesive mounted nameplates may be removed using an induction heater. Technician B says that nameplates can be removed with fishing line. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 6

Technician A says that a castle nut and a self locking nut are both a one-time use fastener. Technician B says that internal snap rings are fasteners that fit into a groove on the outside of a part. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 7

Technician A says that an SPR is commonly used to bonding aluminum parts. Technician B says that to "R& I" a part means a technician will remove and install the same part. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 8

____________________ washers are used to spread out the clamping force of the fastener.

Question 9

Technician A says that most threaded SAE and Metric fasteners such as bolts are inter-changeable with each other. Technician B says a thread pitch gauge will tell the diameter of a bolt. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 10

Technician A says that if a bolt has a grade of 4.6 marked on its head, it is an SAE bolt with a 4.6 thread pitch. Technician B says that an SAE grade 2 bolt will have no slash markings on it. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 11

Weatherstripping is always attached with adhesives.

Question 12

Self-tapping screws are used to hold sheet metal together.

Question 13

Bolts come in both right-handed and ____________________ thread.

Question 14

To loosen a right-handed thread bolt, it should be turned to the left.

Question 15

A technician is removing a weatherstripping which has 34 plastic fasteners. 50% of the fasteners break during removal. The technician needs to purchase ____________________ fasteners. (How many?)

Question 16

Technician A says that the use of protective mechanics gloves is important when removing trim and is part of personal protective clothing of a repair technician. Technician B says safety glasses should be worn at all times when working in a collision repair shop. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 17

Technician A says that "bagging and tagging" is a method commonly used to organize screws and hardware while the vehicle is being dismantled. Technician B says that most screws and hardware are replaced with new so one need not worry about the proper labeling and storing of removed parts Who is correct?

A) A only
B) B Only
C) Both A and B
D) Neither A nor B

Question 18

An SAE grade 5 bolt will have ____________________ slash marks on its head.

Question 19

Technician A says some emblems have guide pins on them to help align them properly. Technician B says wet installing decals allows you to move and shift them around slightly. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 20

Which of these exterior trim items would least likely be removed as opposed to masking?

A) Cladding
B) Belt Molding
C) Weatherstripping
D) windshield reveal molding

Question 21

Why should a technician aim to make each collision repair an undetectable repair?

Question 22

Explain how a self-locking nut works.

Question 23

Explain why parts should be labeled and stored when removed from a vehicle during repair.

Question 24

Explain why weatherstripping is needed around a door.

Question 25

Describe how SAE bolt grading can be recognized by a technician.