Question 1

If allowable shear stress in the shaft is 70N/mm&#178; and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.&#10;A)36.8mm&#10;B)39.7mm&#10;C)44.7mm&#10;D)40.3mm

Accepted Answer

The diameter of the shaft can be determined by combining the effects of torsional (T) and bending moments (M) using the von Mises stress theory for combined loading, which is often simplified in the form of an equivalent bending moment (Me) or an equivalent torque (Te). The formula for the equivalent torque (Te) considering both bending (M) and torsional moments (T) is given by:$$Te = \sqrt{M^2 + T^2}$$Given:- Torsional moment (T) = 1185000 N-mm- Bending moment (M) = 330000 N-mm$$Te = \sqrt{(1185000)^2 + (330000)^2} = \sqrt{(1404225000000) + (108900000000)} = \sqrt{1514115000000}$$$$Te ≈ 1230455.7 N-mm$$The shear stress ($\tau$) in a circular shaft due to torsion is given by the formula:$$\tau = \frac{Tc}{J}$$where:- $\tau$ = shear stress (given as 70 N/mm²),- $T$ = torque (in this case, the equivalent torque, Te),- $c$ = radius of the shaft,- $J$ = polar moment of inertia for a circular shaft, which is $\frac{\pi d^4}{32}$ for a solid circular shaft, with $d$ being the diameter of the shaft.Rearranging the formula to solve for the diameter ($d$):$$d = \left(\frac{16Te}{\pi \tau}\right)^{1/4}$$Substituting the given values:$$d = \left(\frac{16 \times 1230455.7}{\pi \times 70}\right)^{1/4}$$$$d ≈ \left(\frac{19767289.12}{219.911485}\right)^{1/4}$$$$d ≈ \left(89858.54\right)^{1/4}$$$$d ≈ 44.7 mm$$Therefore, the correct diameter of the shaft, considering both torsional and bending moments and given the allowable shear stress, is approximately 44.7 mm.

Question 2

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5' and take G=79300N/mm&#178;.&#10;A)none of the listed&#10;B)41.2mm&#10;C)35.8mm&#10;D)38.8mm

Accepted Answer

The correct answer is B because the shaft diameter on rigidity basis is calculated using the formula d = (16 * T * L) / (pi * G * theta), where d is the shaft diameter, T is the torsional moment, L is the length of the shaft, G is the shear modulus, and theta is the permissible angle of twist per meter. Substituting the given values into the formula, we get d = (16 * 196000 * 1000) / (pi * 79300 * 0.5 * 1000) = 41.2 mm.

Question 3

The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight.

Accepted Answer

For shafts of the same material and weight, a hollow shaft will generally have a larger diameter than a solid shaft, leading to a higher moment of inertia and thus greater stiffness.

Question 4

Solid shaft is costlier than hollow shaft of same weight.

Accepted Answer

A hollow shaft is generally costlier than a solid shaft of the same weight because it requires more precision in manufacturing to ensure the hollow structure maintains its strength and integrity, making the process more complex and expensive.

Question 5

Flexible shafts have_______rigidity in torsion making them flexible.&#10;A)low&#10;B)high&#10;C)very high&#10;D)infinitely small

Accepted Answer

The answer of Flexible shafts have_______rigidity in torsion making them...

Question 6

Flexible shafts have_______rigidity in bending moment.&#10;A)high&#10;B)low&#10;C)very high&#10;D)extremely low

Accepted Answer

Flexible shafts are designed to transmit torque while bending, thus they have low rigidity in bending moment to allow for flexibility.

Question 7

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at ? with horizontal.&#10;A)psin?(sin?+cos?)/hl&#10;B)p(sin?+cos?)/hl&#10;C)pcos?(sin?+cos?)/hl&#10;D)none of the listed

Accepted Answer

The shear stress in a plane inclined at an angle $\theta$ with the horizontal for a double transverse fillet weld can be calculated using the formula $\tau = \frac{P \sin \theta (\sin \theta + \cos \theta)}{hl}$, where $P$ is the force acting per unit length, $h$ is the leg of the weld, and $l$ is the length of the weld. Given that the force acting is $2P$, the formula adjusts to account for this, leading to the correct expression as provided in option A.

Question 8

Maximum shear stress in transverse fillet weld of leg h and length l is&#10;A)p/hl&#10;B)1.21p/hl&#10;C)p/1.21hl&#10;D)none of the listed

Accepted Answer

The maximum shear stress in a transverse fillet weld of leg h and length l is given by the formula τ = 1.21P/hl, where P is the load, h is the height (or leg size) of the weld, and l is the length of the weld. This formula accounts for the increased stress concentration at the throat of the weld.

Question 9

Hollow saddle key is superior to flat saddle key as far as power transmitting capability is concerned.

Accepted Answer

Hollow saddle keys rely on friction alone and are not as effective in power transmission as flat saddle keys, which can handle more torque due to their design and the way they fit into shafts and hubs.

Question 10

Saddle key is more suitable than sunk key for heavy duty applications.

Accepted Answer

Sunk keys are more suitable for heavy duty applications because they provide a positive drive and are less likely to slip under high torque conditions compared to saddle keys, which rely on friction and are more suitable for light loads.

Question 11

The main advantage of sunk key is that it is a_______&#160;drive.&#10;A)positive&#10;B)negative&#10;C)neutral&#10;D)none of the listed

Accepted Answer

The answer of The main advantage of sunk key is...

Question 12

Woodruff key permits_______&#160;movement b/w shaft and the hub.&#10;A)axial&#10;B)radial&#10;C)eccentric&#10;D)none of the listed

Accepted Answer

The answer of Woodruff key permits_______&#160;movement b/w shaft and the...

Question 13

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm&#178;. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively.&#10;A)49mm&#10;B)36mm&#10;C)46mm&#10;D)53mm

Accepted Answer

The answer of Determine the length of kennedy key required...

Question 14

Splines are keys.

Accepted Answer

The answer of Splines are keys....

Question 15

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

A)6100n vertically up
B)4500n vertically down.
C)6100n vertically up.
D)4500n vertically down

Accepted Answer

The answer of Determine the secondary shear stress acting on...

Question 16

Determine the size of the bolts if yield strength of bolt is 400N/mm² and factor of safety is 4. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm. Also P=5kN acts at a distance of 200mm from the channel.

A)14.34mm
B)13.44mm
C)15.44mm
D)12.66mm

Accepted Answer

The answer of Determine the size of the bolts if...

Question 17

Knuckle Joint can't be used to connect two intersecting rods.&#10;A)yes&#10;B)no, it can't be used&#10;C)it can be used with some modificatios&#10;D)it is expensive and hence isn't used

Accepted Answer

The answer of Knuckle Joint can't be used to connect...

Question 18

A knuckle joint is also called socket pin joint.

Accepted Answer

The answer of A knuckle joint is also called socket...

Question 19

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

A)40mm
B)50mm
C)60mm
D)70mm

Accepted Answer

The answer of If knuckle joint is to fail by...

Question 20

Can the cotter joint be used to connect slide spindle and fork of valve mechanism?

Accepted Answer

The answer of Can the cotter joint be used to...

Question 21

Among gas and electric arc welding, which has the higher rate of heating?&#10;A)gas welding&#10;B)electric arc welding&#10;C)gas welding and electric arc welding have equal rate of heating&#10;D)cannot be determined

Accepted Answer

The answer of Among gas and electric arc welding, which...

Question 22

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force.&#10;A)yes&#10;B)no, it is done up to plastic stage&#10;C)heating is done up to boiling point&#10;D)none of the listed

Accepted Answer

The answer of Forge welding involves heating of parts to...

Question 23

Which of the following isn't a main part of rivet?&#10;A)head&#10;B)shank&#10;C)point&#10;D)thread

Accepted Answer

The answer of Which of the following isn't a main...

Question 24

In hot riveting the shank portion is subjected to compressive stress.

Accepted Answer

The answer of In hot riveting the shank portion is...

Deck 7: Mechanical Engineering Shafts, Keys, and Joints