Deck 15: Fixture and Equipment Installation

Question 1

A two-piece toilet is assembled by a plumber on a job site.

Answer 1

True

Question 2

A ____________________ has a designated port to connect the dishwasher drain hose.

Answer 2

garbage disposer

Question 3

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
A type of connection used for water distribution tubing.

Answer 3

C

Question 4

Some codes require a dishwasher drain hose to be routed through an air gap device.

Question 5

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
Non-corrosive bolts inserted into a closet flange to anchor the toilet to the drainage system.

Question 6

A ____________________ is installed to connect the stub-out pipe to the p-trap outlet.

Question 7

Testing fixture installations is performed with a performance test and a pressure test.

Question 8

A _______________ is installed on all sinks and connects the fixture outlet to the rough-in stub-out pipe.

Question 9

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
A pipe size that is smaller in diameter and has a thinner wall thickness than pipe used for drainage piping.

Question 10

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
A drain assembly used to connect a double-bowl kitchen sink to a single p-trap.

Question 11

A plumber usually installs a dishwasher.

Question 12

A toilet is installed onto a _______________ flange with a _______________ seal and a set of _______________ bolts.

Question 13

Turning a metal escutcheon in the opposite direction and installing it temporarily over the pipe will bend the tabs inward and enable an easier fit around the stub-out pipe.

Question 14

The drain from a dishwasher typically connects to the drain from a ____________________.

Question 15

Many codes mandate that an HVAC contractor installs the venting (flue)system on a gas water heater.

Question 16

Most fixture installations occur during the rough-in phase of construction.

Question 17

A kitchen faucet is typically installed after installing a new kitchen sink.

Question 18

A wax toilet seal will never have to be heated.

Question 19

The water connection to a toilet requires a specific supply tube known as a ____________________.

Question 20

When installing a stop that is soldered onto copper,the ____________________ and ____________________ is typically removed so the rubber washer is not damaged.

Question 21

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
Floor or wall plate installed around a stub-out pipe to conceal the penetration.

Question 22

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
Also called a toilet flange;installed to connect a toilet to the drainage system.

Question 23

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
A slip joint-style fitting installed to connect a tubular p-trap to the drainage system.

Question 24

MATCHING
Match the following terms:
a.Escutcheon
b.Wax seal
c.Compression
d.Trap adapter
e.Tubular
f.Closet bolts
g.Closet flange
h.Continuous waste
A seal that ensures water does not leak and sewer gases do not escape when connecting the toilet to the drainage system.