Deck 5: Hand Tools and Shop Equipment

Question 1

A 12-point socket has more grip than a 6-point socket.

Answer 1

False

Question 2

When installing a new hacksaw blade, the teeth should face rearward.

Answer 2

False

Question 3

What type of wrench should be used to loosen or tighten brake lines or tubing fittings?

A) open-end
B) box-end
C) combination
D) flare nut

Answer 3

D

Question 4

One bar equals one pound per square inch.

Question 5

An extractor is used for removing broken ______.

A) seals
B) bushings
C) pistons
D) bolts

Question 6

The acetylene tank can be placed horizontally or vertically when heating and cutting with an oxyacetylene torch.

Question 7

A telescoping gauge may be used to measure the outside diameter of an object.

Question 8

The tensile strength of a metric bolt can be identified by ______.

A) numerical grade markings
B) radial lines
C) both "numerical grade markings" and "radial lines"
D) neither "numerical grade markings" nor "radical lines"

Question 9

Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip?

A) standard
B) torx
C) pozi-drive
D) clutch head

Question 10

One liter equals 3.7854 gallons.

Question 11

Ten inch pounds of torque equals 13.558 Newton (N) meters.

Question 12

Metric and SAE wrenches are interchangeable.

Question 13

One square inch equals 6.452 square centimeters.

Question 14

Bolt length is measured from the top surface of the head to the end of the threads.

Question 15

One liter equals 61.02 cubic inches.

Question 16

Which of the following types of pliers is best for grasping small parts?

A) adjustable
B) needle-nose
C) retaining ring
D) snap ring

Question 17

Which source of information will give you the most detail about a specific system or part?

A) automotive technology textbooks
B) aftermarket system service manuals
C) owner's manual
D) manufacturers' service manual

Question 18

The United States passed the Metric Conversion Act in 1985.

Question 19

One inch equals 2.54 centimeters.

Question 20

A tapered punch is used to line up bolt holes.

Question 21

Technician A says coarse threaded bolts are used where superior holding force is necessary. Technician B says bolts that have rolled threads are 30 percent stronger than bolts with cut threads. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 22

Which screwdriver design has a square tip?

A) pozi-drive
B) torx
C) clutch
D) scrulox

Question 23

In an oxyacetylene welding torch the acetylene hose is colored _____.

A) red
B) blue
C) green
D) yellow

Question 24

A straightedge and feeler gauge are used to measure _____.

A) clearances
B) warpage
C) runnout [wobble]
D) endplay

Question 25

Technician A says a bolt may break because the fillet is damaged. Technician B says that a bolt may become fatigued and break if it is undertightened. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 26

A 3/8 inch UNC bolt is being discussed. Technician A says that the bolt diameter is 3/8 inch and that it has 16 threads per inch. Technician B says that the bolt meets the measurement standards developed by the University of North Carolina. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 27

If the number 8.8 is stamped on the head of a bolt, the bolt is ______.

A) a metric bolt
B) a UNC bolt
C) a UNF bolt
D) a grade 8 bolt

Question 28

All the following are types of lifts EXCEPT:

A) frame contact
B) body contact
C) wheel contact
D) axle engaging

Question 29

Which of the following measurements requires the use of a precision straightedge as well as a feeler gauge?

A) piston ring end gap
B) connection rod side clearance
C) crankshaft end play
D) cylinder head warpage

Question 30

Each number on the sleeve of a metric micrometer represents _____ mm.

A) .05
B) .005
C) 5
D) none of these answers is correct

Question 31

NPT stands for ______.

A) nickel plated threads
B) nonplated threads
C) nominal proportion thread
D) national pipe thread

Question 32

Technician A torques critical parts using an impact wrench. Technician B torques critical parts with an air ratchet. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 33

A measurement must be made within one ten-thousandth of an inch. Technician A uses a machinist's rule. Technician B uses a standard micrometer. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 34

Technician A says a tap cuts external threads. Technician B says a die cuts internal threads. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 35

Technician A uses a small hole gauge and micrometer to measure the inside diameters of small bores. Technician B uses a dial caliper to take depth measurements. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 36

The bolts used to attach an engine sling to the engine must thread into the cylinder head or block _____ times the diameter of the bolt.

A) 1
B) 1

C) 2
D) 2

Question 37

Technician A says antiseize compound is used to prevent bolts from seizing in aluminum. Technician B says thread sealant is used to prevent leaks. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 38

Machine screws can have a(n) _____ head.

A) round
B) torx
C) oval
D) all answers are correct

Question 39

Technician A says a vernier caliper can be used to measure the outside diameter of something. Technician B says a vernier caliper can be used to measure the inside diameter of a bore. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 40

Technician A uses a punch to align holes in parts during assembly. Technician B uses a punch to drive out rivets. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 41

The two systems of weights and measures that exist side by side in the United States are the British Imperial (U.S. customary) system and the ____________________ system.

Question 42

Combination pliers are often called ____________________ pliers.

Question 43

A telescoping gauge is also called a(n) ____________________ gauge.

Question 44

Turning effort [the amount of torque it takes to maintain rotation of a gear or shaft] can be easily measured using a _____type torque wrench.

A) click
B) dial
C) digital readout
D) all answers are correct

Question 45

A(n) ____________________ gauge is used to measure the number of threads per inch on a bolt.

Question 46

A(n) ____________________ wrench has one fixed jaw and one movable jaw.

Question 47

Technician A removes rivets with a hammer and screwdriver. Technician B removes rivets with a hammer and punch. Who is correct?

A) A only
B) B only
C) both A and B
D) neither A nor B

Question 48

A dial caliper is accurate to _____ inch.

A) .0001
B) .001
C) .002
D) .010

Question 49

The ____________________ wrench has an open-end jaw on one end and a box-end on the other.

Question 50

A(n) ____________________ screwdriver has a six-pronged tip.

Question 51

A(n) ____________________ press is used to install piston pins, axle bearings, drum and rotor studs.

Question 52

A(n) ____________________ punch is used to make an indent prior to drilling a hole in a steel bracket.

Question 53

A(n) ____________________ manual contains standards for the length of time a specific repair is supposed to require.

Question 54

A(n) ____________________ extension allows the socket to pivot up to 16 degrees.

Question 55

Trouble lights are designed to use a standard incandescent bulb or a(n) ____________________ bulb.

Question 56

To prevent vibration from loosening the fasteners, locknuts have _____ inserted into a section of the threads.

A) copper
B) aluminum
C) polycarbonate
D) nylon

Question 57

A(n) ____________________ gauge is a thin strip of metal or plastic of known and closely controlled thickness.

Question 58

A(n) ____________________ hammer should be used to install gears and shafts in a transmission.

Question 59

To avoid personal injury, files should always be used with a(n) ____________________.

Question 60

A UNC bolt with three radial lines (marks) on its head has a tensile strength grade of ____________________.

Question 61

How are hammers identified?

Question 62

What determines the size of an open-end wrench?

Question 63

List three types of wheels available for use with a bench grinder.

Question 64

Identify and describe the purpose of three washer designs used with fasteners.

Question 65

Identify some common uses of a dial indicator.

Question 66

What are some safety issues concerning the use of power tools?

Question 67

Name the parts of a bolt.

Question 68

What is the best source for vehicle identification?

Question 69

How often should the calibration of a micrometer be checked?

Question 70

Describe the proper usage of a hacksaw.

Question 71

Describe how manufacturers inform technicians about changes in current model year vehicle specifications and repair procedures.