Deck 2: Hand Power Tools

Question 1

A compound miter cut is a combination of a bevel and miter cuts

Answer 1

True

Question 2

A chamfer is a small bevel on the edge of stock

Answer 2

True

Question 3

A full set of ____ bits ranges in size from 1/4 to 1 inch, graduated in 1/16-inch increments.

A)expansive
B)speed
C)power bore
D)auger

Answer 3

D

Question 4

The ____ saw, sometimes called a Sawzall, is used primarily for roughing in work.

A)chamfer
B)reciprocating
C)transverse
D)lateral

Question 5

A light-duty specialized type of router is called a ____ trimmer.

A)form
B)shape
C)layered
D)laminate

Question 6

____ are used extensively for fastening gypsum board to walls and ceilings with screws.

A)Screwguns
B)Caulking guns
C)Blowguns
D)Heat guns

Question 7

Some twist bits are designed to drill into metal as well as other materials.

Question 8

Masonry drill bits have ____ tips for drilling holes in concrete, brick, tile, and other masonry.

A)zinc
B)nickel
C)carbide
D)tungsten

Question 9

Cordless circular saws cannot cut dimension lumber.

Question 10

____ drills can deliver as much as 50,000 hammer blows per minute on the drill point.

A)Geared head
B)Hammer
C)Radial arm
D)Mill

Question 11

Brad nailers are used to fasten thin materials.

Question 12

Sometimes called the ____, the portable electric circular saw is used by the carpenter more than any other portable power tool.

A)Skilsaw
B)hacksaw
C)ripsaw
D)coping saw

Question 13

The guard of a circular saw should never be retracted by hand.

Question 14

Twist drills range in size from 1/16 to 1 inch in increments of ____ inch

A)1/64
B)1/16
C)1/8
D)1/4

Question 15

The size of a portable electric circular saw is determined by the diameter of the blade.

Question 16

Portable power planes have an adjustable ____ that allows planing square, beveled edges to 45 degrees, or chamfers.

A)chuck
B)blade
C)fence
D)bit

Question 17

When loosing the bolt holding a circular saw blade, it should be rotated opposite to the normal rotation of the blade.

Question 18

Hammer drills are best suited drilling into wood.

Question 19

The saber saw is sometimes called a ____.

A)compass saw
B)wallboard saw
C)jigsaw
D)keyhole saw

Question 20

The size of a drill is determined by the capacity of the chuck.

Question 21

____-actuated drivers are used to drive specially designed pins into masonry or steel.

A)Pneumatic
B)Powder
C)Battery
D)Hand

Question 22

The portable ____ sander is used frequently for sanding cabinetwork and interior finish.

A)disc
B)belt
C)drum
D)stroke

Question 23

Finishing sanders either have a(n) ____ motion, an oscillating (straight back-and-forth) motion, or a combination of motions controlled by a switch.

A)orbital
B)hyperbolic
C)parabolic
D)lateral

Question 24

The material removed when cutting with saw blades creates a space called the __________.

Question 25

__________ cutting is done by rotating a tool base so the spinning blade cuts into the material.

Question 26

Drill bits designed to cut fast holes in wood are called __________.

Question 27

A electrical tool designed to replace the bench plane is called __________.

Question 28

The heavy-duty ____ drives smooth-shank, headed nails up to 3 1/4 inches, ring-shank nails up to 2 3/8 inches, and screw shank nails up to 3 inches.

A)finish nailer
B)brad nailer
C)framing gun
D)roofing nailer

Question 29

A device used to protect from power cord electrical shocks is called a __________.

Question 30

Pneumatic staplers and nailers are commonly called ____.

A)tubes
B)rods
C)blasters
D)guns