Deck 8: Shop Tools

Question 1

8)Which of the following socket drives is LEAST-Likely to be used on an automobile?

A) 1/4"
B) 3/8"
C) 1/2"
D) 3/4"

Answer 1

D

Question 2

4)A torque wrench is used to tighten a fastener a prescribed amount.

Answer 2

True

Question 3

5)A hammer is used to secure a bearing to a shaft or hold it inside of a housing.

Answer 3

False

Question 4

14)While discussing air compressors, Technician A says that air pressure should be regulated to 40 psi to get the best performance and reliability from air tools. Technician B says that air pressure should be regulated at 60 psi.

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 5

11)A wrench head that has been adapted so that it can be used with a ratchet and extension is MOST-Likely referred to as a(n):

A) crowfoot socket.
B) impact socket.
C) wobble socket.
D) swivel socket.

Question 6

12)Which of the following is LEAST-Likely to be a type of pliers?

A) Rib joint
B) Needle nose
C) Allen head
D) Slip-joint utility

Question 7

2)The flare-nut wrench has an opening on one of its sides that allows it to slip over a fuel line.

Question 8

10)When removing a nut from a long stud, the MOST-Likely tool used to provide clearance is the:

A) spark plug.
B) screwdriver.
C) deep socket.
D) wrench.

Question 9

13)While having a discussion about hammers, Technician A says that pounding on a chisel with too large a hammer can cause chips in the chisel head. Technician B says that a hammer head should be no more than 3.8" larger in diameter than the head of the punch or chisel. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 10

9)Each of the following represent common sizes of extensions EXCEPT:

A) 2"
B) 3"
C) 6"
D) 10"

Question 11

19)____________________ are pieces of metal that come off the workpiece during filing.

Question 12

17)A(n) ____________________ is a hex tool used to turn setscrews and capscrews.

Question 13

16)Most automotive technicians own their own set of ____________________, including items like sockets, wrenches, and screwdrivers.

Question 14

6)A(n) ____ is sometimes used to loosen or tighten parts such as muffler clamps or steering linkage tie-rod end clamps.

A) crescent wrench
B) ratcheting box wrench
C) Allen wrench
D) adjustable wrench

Question 15

20)____________________ are used to remove or install pressed-fit parts on shafts, like gears, bushings, and bearings.

Question 16

7)When a nut or bolt is extremely tight, a ____ is used so that the teeth in the ratchet head are not damaged.

A) socket
B) breaker bar
C) ratchet
D) clutch

Question 17

1)A favorite among professional technicians is the combination wrench , which includes a box wrench and an open-end wrench on one end or the other.

Question 18

18)A(n) ____________________ is similar to a Phillips head, but it has little wings on the inside that provide a slightly better grip and hold onto fasteners for easier assembly work.

Question 19

15)All of the following are components of a simple planetary gear EXCEPT:

A) the impact socket.
B) the sun gear.
C) the planetary carrier or cage.
D) the three pinion gears.

Question 20

3)A #1 Phillips head is larger than a #2.

Question 21

24)Provide four tips on proper hacksaw usage.

Question 22

23)What is the difference between a clutch head and a Scrulox screwdriver?

Question 23

25)Name four precautions you should take when using a puller.

Question 24

22)Why is it not advisable to use a Reed and Prince on automotive screws?

Question 25

21)What is the difference between a ratcheting box wrench and an adjustable wrench?