Deck 9: General Shop Equipment

Question 1

A hydraulic jack has a fluid reservoir and three one-way check valves.

Answer 1

False

Question 2

All of the following are hydraulic equipment EXCEPT:

A)jacks
B)shop cranes
C)presses
D)breaker bars

Answer 2

D

Question 3

Which of the following statements is LEAST-Likely true?

A)Every shop has a vise.
B)Shops that sell or repair tires have a tire changer.
C)High-pressure air is used to unseat the bead of a tire from the wheel rim.
D)An engine analyzer is not useful in diagnosing certain engine problems like compression problems and uneven balance between cylinders.

Answer 3

D

Question 4

The MOST-Likely type of arc welding used in automotive shops is:

A)cherry picker
B)MIG welding
C)runout
D)chain fall

Question 5

You can hammer on a vise, except on the anvil portion that some vises have.

Question 6

A(n) ____________________ has small wheels and saves wear and tear on a body when working in uncomfortable positions or working under a car that is resting on vehicle support stands.

Question 7

During a recent discussion, Technician A says that an engine analyzer can help to diagnose compression problems, uneven balance between cylinders, worn timing chains, and air leaks. Technician B says that it should never be used to diagnose compression problems or air leaks. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 8

All of the following types of bearings are used in power tools EXCEPT:

A)the armature
B)powdered metal sleeves
C)the roller
D)the ball

Question 9

A shop crane, often called a(n) ____________________, is used to remove the engine from the car.

Question 10

When a chain hoist is used for engine removal, the car's hood must first be removed.

Question 11

____ in a drill motor are located at the front and rear of the motor armature and at the spindle chuck.

A)Brushes
B)Grinders
C)Gears
D)Bearings

Question 12

A drill bit is tightened between the jaws of a chuck with a(n) ____________________.

Question 13

The MOST-Likely part that is attached to the front of a grinder is a:

A)battery charger
B)vise
C)clutch
D)water pot

Question 14

While having a discussion about chuck, Technician A says that chuck runout is allowed to be up to 0.010" in a consumer drill. Technician B says that it is allowed to be 0.005" in a commercial drill. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 15

A(n) ____________________ is used to raise and lower a vehicle and to help position heavier components, such as engines and transmissions.

Question 16

It is not good for the battery to be allowed to remain in a state of discharge.

Question 17

A(n) ____ provides a convenient means of turning the engine over for disassembly and reassembly.

A)arbor
B)engine stand
C)floor creeper
D)hydraulic jack

Question 18

Which of the following statements is LEAST-Likely to be true about oxyacetylene welding?

A)Three compressed gases are stored in separate steel cylinders.
B)Hoses connect the cylinders to the torch where the gases are mixed.
C)When the gases are mixed in the correct proportion and ignited, intense heat is created at the tip of the torch.
D)The heat is intense enough to melt steel for welding or cutting.

Question 19

A cutting lubricant is used to drill all metals except cast iron or aluminum. These metals can be drilled dry or cooled with a water-based coolant or kerosene.

Question 20

A(n) ____________________ is a large, stationary machine used to drill parts that are clamped to the press table.

Question 21

What precautions should you take to avoid having someone accidentally step on a floor creeper?

Question 22

What precautions should you take when lifting an engine sling?

Question 23

What is the difference between a cherry picker and an engine sling?

Question 24

What precautions should you take when using a transmission jack with a car raised on a lift?

Question 25

What is the purpose of an engine analyzer?