Deck 15: Door, Roof, and Glass Service

Question 1

ASE-Style Multiple Choice The ____ is the main steel frame of the door.

A)window regulator
B)door skin
C)door glass
D)door frame

Answer 1

D

Question 2

Electric adhesive cutters plug into 220-volt outlets or use rechargeable battery power to produce a vibrating action that cuts the adhesive around the glass.

Answer 2

False

Question 3

When laminated glass is broken, the plastic material helps to hold the shattered glass in place and prevent it from causing injury.

Answer 3

True

Question 4

If two lift arms are used in the window regulator, it is usually referred to as a Y-type regulator .

Question 5

ASE-Style Multiple Choice ____ is used in the front windshield only and provides added protection against shattering and cuts during impact.

A)Laminated plate glass
B)Tempered glass
C)Antilacerative glass
D)Conventional glass

Question 6

ASE-Style Multiple Choice The ____ is a gear and arm mechanism for moving glass.

A)window regulator
B)door frame
C)door skin
D)door glass

Question 7

ASE-Style Multiple Choice All of the following can be used to make the door skin EXCEPT:

A)aluminum
B)piano wire
C)fiberglass
D)plastic

Question 8

Windshields and rear windows are usually secured in place by rubber weatherstripping or by an adhesive.

Question 9

ASE-Style Multiple Choice ____ is used for side and rear window glass but rarely for windshields.

A)Laminated plate glass
B)Tempered glass
C)Antilacerative glass
D)Conventional glass

Question 10

Worn door hinges show up when the two halves of the hinge body shift, allowing up and down door movement.

Question 11

ASE-Style Multiple Choice ____ fits around the door or door opening to seal the door-to-body joint.

A)Protective tape
B)Piano wire
C)Molding
D)Door weatherstripping

Question 12

ASE-Style Multiple Choice The ____ is the outer panel over the door frame.

A)window regulator
B)door skin
C)door glass
D)door frame

Question 13

Inside rearview mirrors normally attach to the windshield glass using a quick bond adhesive.

Question 14

The door latch engages the door striker on the vehicle body to hold the door closed.

Question 15

A plastic or paper door dust cover fits between the inner trim panel and door frame of a door to keep out wind noise.

Question 16

Adhesive-bonded windshields increase the overall rigidity of the vehicle, minimizing body twist and helping to keep the glass in place during a collision.

Question 17

ASE-Style Multiple Choice ____ surround the sides and top of the door glass with a metal frame.

A)Hard top doors
B)Hood struts
C)Framed doors
D)Cowl panels

Question 18

ASE-Style Multiple Choice ____ is used to make all windshields and some side glass.

A)Laminated plate glass
B)Tempered glass
C)Antilacerative glass
D)Conventional glass

Question 19

The door skin serves as a guide for the glass to move up and down.

Question 20

ASE-Style Multiple Choice ____ have the glass extending up out of the door (when the glass is rolled up)without a frame around it.

A)Frameless doors
B)Hood struts
C)Framed doors
D)Cowl panels

Question 21

ASE-Style Multiple Choice A ____ involves trying to move the door assembly up and down on its hinges.

A)dashboard check
B)caged plate check
C)door hinge check
D)windshield check

Question 22

_________________________ results when the rear of the door is lower than the front.

Question 23

A(n)_________________________ is often needed to reach under the molding to release the clip from under the molding lip.

Question 24

ASE-Style Multiple Choice While having a discussion, Technician A says that the use of oil on rubber or felt window channels is highly recommended. Technician B says oil can cause the rubber or felt to swell and deteriorate. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 25

ASE-Style Multiple Choice Which of the following statements is LEAST-Likely true?

A)Compact wagons have a three-way tailgate that swings open like a door or drops down like a truck tailgate.
B)When servicing a door for a keyless entry system, all wiring harness connectors must be disconnected and reconnected carefully.
C)The three-way tailgate can be operated as a tailgate with the glass fully down or as a door with the glass up or down.
D)Some heating elements built onto rear glass can be repaired when damaged.

Question 26

______________________________ use shop air pressure and a vibrating action to help cut the adhesive around the glass.

Question 27

ASE-Style Multiple Choice While having a discussion, Technician A says that a striker plate should not slide into the latch when a door is closed. Technician B says that the striker plate is not adjusted properly if the door rises or it is forced down when the door is closed. Who is correct?

A)A only
B)B only
C)Both A and B
D)Neither A nor B

Question 28

How would you remove a door lock mechanism?

Question 29

ASE-Style Multiple Choice A(n)____ is a thick, heavy, steel plate with threaded holes to accept large bolts.

A)caged plate
B)cowl panel
C)tailgate
D)air dam

Question 30

List three methods used to attach the door glass to the window lifting or regulator mechanism.

Question 31

Why do you think vehicle manufacturers use weld-bond adhesives?

Question 32

ASE-Style Multiple Choice The part that MOST-Likely belongs to a sunroof design is:

A)the torque bolt
B)the cowl panel
C)the air ratchet
D)the drain plate

Question 33

How would you perform a door weatherstrip service?

Question 34

ASE-Style Multiple Choice Which of the following statements is LEAST-Likely true?

A)The regulator and its associated parts are sometimes riveted, rather than bolted, to the door structure.
B)Some vehicle windows utilize adjustable guide rollers in a moveable channel.
C)After the door and its glass have been adjusted, you must reinstall all of the door trim pieces and other parts.
D)Tailgate glass is generally secured to a regulator with adhesives.

Question 35

ASE-Style Multiple Choice The part that will MOST-Likely be housed in a "cage," or box of thin sheet metal spot welded to the body panel is:

A)the striker
B)the body shim
C)the threaded plate
D)the frame bracket

Question 36

ASE-Style Multiple Choice All of the following are components of a window regulator EXCEPT:

A)a window crank
B)bushing
C)sash channels
D)a set of gears

Question 37

______________________________ consists of two thin sheets of glass with a thin layer of clear plastic (vinyl)between them.

Question 38

____________________ is a transparent substance manufactured by heating a mixture of sand, soda (sodium carbonate), limestone, and other materials to a temperature of about 2,400 ° F (1,300 ° C).

Question 39

List four causes of exterior door handle problems.

Question 40

ASE-Style Multiple Choice A ____ typically consists of a large glass sheet, frame assembly, and motor assembly for sliding the glass back into the rear of the roof panel.

A)door skin
B)sunroof assembly
C)caged plate
D)door frame