Deck 12: Bolted Exterior Panel Replacement

Question 1

The drive mecanism of the window regulator may be a manually operated crank or an electric motor.

Answer 1

False

Question 2

Technician A says one time use fasteners can be saved and used for other applications. Technician B says when installing and adjusting composite panels a specific torque amount and tightening sequence may be required. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Answer 2

B

Question 3

Technician A says that when installing an entire front clip the hood should be installed first as everything must fit around it. Technician B says that when tightening fender bolts, one must exercise extreme caution to avoid applying an excessive amount of force and thus damaging the edge of the crown on the fender. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Answer 3

C

Question 4

Technician A says that many parts such as antenna side marker and hood cushions must be transferred from the old damaged fender to the replacement one. Technician B says that an egg crate design, a high density foam and a collapsible mechanical piston are all designs used for energy absorbers. Who is correct?

A) A only
B) B only
C) Both a and B
D) Neither A nor B

Question 5

A hole or opening in the lower front bumper or grill designed to funnel or direct air over the radiator is an ____________________ dam.

Question 6

A visible shaking and vibration of the entire hood when driving the vehicle caused by the latch and the adjusting bumpers not being properly adjusted puts the panel under tension and allows it to move, or ____________________.

Question 7

A term commonly used synonymously with the front bumper, the ____________________ is the steel bar that is either chrome plated or painted on the front bumper assembly.

Question 8

A door skin is the outside layer or outer skin of a door panel.

Question 9

A chrome or painted trim piece that surrounds the headlights to cover is a ____________________ or headlight cover.

Question 10

The hood latch should be the first item to attach when adjusting the hood.

Question 11

A striker, sometimes called the striker pin or plate, is a device that engages the latch or lock to hold the door, hood, or deck lid in a closed position.

Question 12

Technician A says that tempered glass is used on nearly all side windows of a car. Technician B says that tempered glass is used for the windshield. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 13

The part of the vehicle to which the front door hinges are attached is called the ____________________ pillar.

Question 14

Technician A says that positive flushness may be required between the rear of the rear door and the quarter panel. Technician B says the rubber bumpers on top of the core support are used to eliminate the flutter on the hood. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 15

Technician A says that when replacing and adjusting a hood, one should close it slowly the first time to confirm that the adjustment is correct. Technician B says that fenders can be adjusted without the hood in place. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 16

Technician A says that a bolted-on radiator support can be adjusted a full inch in all directions to accommodate properly aligning the panels. Technician B says that specially designed bolts are commonly used to fasten plastic and composite fenders. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 17

Technician A says LSG is typically used for windshields and the passenger compartment rear glass. Technician B says that ambient temperature is 75 degrees F. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 18

Technician A says that vehicle information stickers do not need to be replaced after a collision. Technician B say that information stickers have part numbers so they can be replaced after collisions. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 19

The hinges on some vehicles are welded to both the door and the hinge pillar.

Question 20

Technician A says that some radiator supports are attached to the frame rail through enlarged holes with a large bushing or isolator to accomodate proper adjustment. Technician B says door hinges that are welded to the body and to the door are not adjustable. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 21

Explain ambient temperature.

Question 22

What causes wind leaks and turbulent noise?

Question 23

What is a lift gate?

Question 24

What is edging or edge painting?

Question 25

Explain what a floating hinge plate is.