Deck 26: Masking Materials and Procedures

Question 1

When masking for blending, the adjacent panels are masked to accomplish complete coverage of them with clear coat as well.

Answer 1

True

Question 2

Technician A says that reverse masking or bridge masking a series of layers of paper is used so one layer can be pulled off with each successive coat of material applied. Technician B says that a good painter does not need to remove any parts that are not to be painted. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Answer 2

A

Question 3

Technician A says The type of repair made on the vehicle should have little or no bearing on the masking that is done on the vehicle. Technician B says that any part that is not to be partially or completely painted should be removed. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Answer 3

D

Question 4

Technician A says that when a new product is introduced into the refinish department, it should be accompanied with a MSDS provided by the manufacturer. Technician B says that an MSDS for a similar product can be used to determine the personal protective devices that must be used when using the product. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 5

Paper machines come in many different sizes and configurations and greatly speed up the process of masking.

Question 6

Technician A says all aperatures should be masked prior to washing the vehicle to prevent water from getting into and collecting inside the gaps and openings. Technician B says only the part of the vehicle that is to be painted should be cleaned with wax and grease remover before masking. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 7

When masking for priming, overspray is not a problem, and 12" of paper will be enough to protect the vehicle.

Question 8

Masking is done to ____________________ the parts of the vehicle where new finish is unwanted.

Question 9

When a vehicle is being masked for panel painting, the finish will be sprayed on the entire panel.

Question 10

Technician A says that masking is largely done to protect the moldings and trim from overspray as it is difficult to remove from the intricate surfaces that often accompany them. Technician B says that overspray is not a problem as the detail department is responsible for removing it when the car is cleaned prior to delivery. Who is correct?

A) A only
B) B only
C) both A and B
D) Neither A nor B

Question 11

An aftermarket part has arrived in the refinish department. Two technicians have been assured that the black coating is an e-coat primer, but they disagree about how to proceed. Technician A says that it is OK, and it only need to be sanded prior to finishing it. Technician B says that they should perform a wipe-down test to be assured that it is a thermoplastic product. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 12

When masking for priming, it is not necessary to use aperture tape. If primer gets in the cracks, it can be wiped off at any time.

Question 13

Technician A says it is necessary to re-wash the vehicle when it comes to the refinish department, even though it was washed when it first came into the shop. Technician B says that when washing a vehicle, it should be washed with soap and water, using a two-bucket method. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 14

Wax and grease ____________________ is used to chemically clean a part prior to be painted

Question 15

Technician A says the thicker the masking paper is the more resistant it is to solvent penetration. Technician B says the thinner paper is usually more conformable. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 16

____________________ masking is a type of masking that is sprayed onto the vehicle to protect it from overspray.

Question 17

Technician A says buying more expensive masking paper is a waste of money as all work equally well. Technician B says that paper comes in 12" rolls that should be taped together if extra width is required. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 18

When tape is placed half on and half off the back side of a part the masking is applied to it is called ____________________ masking

Question 19

Technician A says liquid mask for vehicles is also made to be used on the booth walls. Technician B says that there is even a liquid mask made specifically for booths' floors. Who is correct?

A) A only
B) B only
C) Both A and B
D) Neither A nor B

Question 20

When paper is placed on a vehicle and folded back on itself to soften the edge, this is called ____________________ masking

Question 21

Describe the process for masking off a quarter panel with a flush mount molding on the stationary side glass.

Question 22

Why is it best to leave some of the masking paper on a vehicle that needs to be polished?

Question 23

Explain the importance of masking for an efficient and professional paint job.

Question 24

Why should a vehicle be masked from the inside out?

Question 25

Two vehicles come into the paint shop at the same time. The one that is scheduled to leave later is the vehicle that can be finished in the least amount of time. Do you move it up and mask it first, or do the vehicle that is scheduled to leave first, and why?