Deck 11: Cable Installation

Question 1

The inner edge of any bend in nonmetallic sheathed cable cannot be less than __________ times the cable diameter.

A) 6
B) 5
C) 4
D) 3

Answer 1

B

Question 2

Romex is considered to be supported when it passes through bored or punched holes in framing members that are no more than 4 1/2 feet apart.

Answer 2

True

Question 3

Even though the NEC permits Type NM cable to be used in one- and two-family homes, it may not be approved for use in your area by the AHJ.

Answer 3

True

Question 4

Which of the following is not a type of nonmetallic sheathed cable?

A) Type NM
B) Type NM-B
C) Type NMC
D) Type NM-U

Question 5

The radius of the curve of the inner bend in Armored Cable must not be less than __________ times the diameter of the cable.

A) 3
B) 4
C) 5
D) 6

Question 6

A 'homerun' may enter a loadcenter through knockouts in the back, sides, top, or bottom of the loadcenter.

Question 7

Type MC cable with an interlocked armor or corrugated sheath cannot be bent to a radius of less than __________ times the external diameter of the metallic sheath.

A) 3
B) 5
C) 7
D) 9

Question 8

The electrician can incorporate waste from rough and finish wiring phases into the jobsite-recycling system.

Question 9

The NEC requires insulated staples to be used when securing and supporting Type NM cable.

Question 10

Romex must be secured at no more than __________ inches from all electrical boxes except a nonmetallic single-gang box.

A) 6"
B) 8"
C) 10"
D) 12"

Question 11

An insulated anti-short fitting required to be installed in the ends of Type AC cable to protect the wires from abrasion is typically called a(n) __________.

A) orange head
B) red head
C) blue devil
D) blue head

Question 12

Cables run along the sides of framing members must be installed at least __________ from the nearest edge of studs, joists, or rafters.

A) 3"
B) 6"
C) 1-1/4"
D) None of the above

Question 13

In attics not accessible by permanent stairs or ladders, Romex run across the top of floor joists within __________ of the scuttle hole must be protected by means such as guard strips.

A) 3'
B) 5'
C) 6'
D) 7'

Question 14

Suspended ceiling grids are permitted by the NEC to support nonmetallic sheathed cables.

Question 15

Romex installed in either a metal or plastic two-gang device box with interior cable clamps, must be secured no more than __________ from the device box.

A) 6"
B) 8"
C) 10"
D) 12"

Question 16

Type MC cable of sizes 14, 12, and 10 AWG must be secured within 12" from every box and then must be supported at intervals not exceeding __________.

A) 4.5'
B) 5'
C) 6'
D) 7'

Question 17

When service entrance cable is used for branch circuits, the only conductor permitted to be bare is the equipment grounding conductor.

Question 18

If a hole is bored into a stud and there is less than 1 1/4" between the edge of the hole and the edge of the stud, a steel plate at least 1/16" thick or a listed and marked steel plate that is less than 1/16" if it still provides equal or greater protection against nail or screw penetration, must be used.

Question 19

In new installations, service entrance cable with an uninsulated conductor (Type SEU) is permitted to be used in branch circuits for an electric range.

Question 20

During the rough-in wiring phase, an electrician always routes cable through floors or ceilings, which provides shorter routes than do perimeter walls.

Question 21

When installing Type MC cable in a house, an anti-short bushing (red head) is required at each end to provide protection for the conductors from the sharp edges of the cable armor.

Question 22

If Type AC is run through a hole in a framing member that has an edge closer than ____________________ inch(es) to the edge of the framing member, it must be protected by a metal plate at least 1/16" thick.

Question 23

The NEC requires at least __________ of free conductor in electrical device boxes for connection to switches and receptacles.

A) 6"
B) 8"
C) 10"
D) 12"

Question 24

Explain the use of running boards in unfinished basements.

Question 25

The maximum distance between supports for a Type NM cable is __________.

A) 3 feet
B) 4 1/2 feet
C) 6 feet
D) 10 feet

Question 26

When installing Romex into a single-gang nonmetallic device box, the cable must be secured no more than __________ from the box.

A) 8"
B) 10"
C) 12"
D) None of the above

Question 27

Which of the following cables are not permitted to be secured directly to the bottom edge of joists in an unfinished basement?

A) 6/2 NM cable
B) 6/3 NM cable
C) 8/2 NM cable
D) 8/3 NM cable

Question 28

Type AC cable must be supported at intervals not exceeding ____________________ feet along the run.

Question 29

Unrolling cable from a coil is very easily done with a device commonly called a __________.

A) spinner
B) roller
C) reel jack
D) fish tape

Question 30

The part of a branch circuit that originates in the loadcenter and provides electrical power to the first electrical box in a circuit is called a __________.

A) ground out
B) home run
C) fly ball
D) strike out

Question 31

Type NM cable is often purchased in __________ foot rolls that are packaged in plastic wrapping or in cardboard boxes.

A) 100
B) 150
C) 250
D) 1000

Question 32

When unrolling cable from a coil, the best way is to pull the cable out of the coil from the __________.

A) outside of the coil
B) inside of the coil
C) underside of the coil
D) None of the above

Question 33

If a cable is placed in a notch in wood studs or other wood framing members, a steel plate at least ____________________ inch thick must be used to protect the cable.

Question 34

Manufacturers of Type NM cable are now color coding their cables. The color typically used for 12 AWG Romex cable is __________.

A) red
B) blue
C) yellow
D) orange

Question 35

Explain why the sheathing of nonmetallic sheathed cable should extend into the device box or beyond the cable clamp approximately 1/4".

Question 36

In single-gang nonmetallic electrical device boxes, at least __________ of the cable sheathing must extend into the box.

A) 1/8"
B) 1/4"
C) 1/2"
D) 3/4"

Question 37

Explain what type of protection must be used when running Romex through bored or punched holes in metal studs.

Question 38

All of the following cable types are typically used in residential wiring except __________.

A) Type NM
B) Type AC
C) Type MI
D) Type MC

Question 39

Where passing through a floor and located on the outside of a wall, nonmetallic sheathed cable must be enclosed in rigid metal conduit, intermediate metal conduit, electrical metallic tubing, or Schedule 80 rigid PVC conduit extending at least ____________________ inches above the floor.

Question 40

Electricians commonly refer to Armored Clad Cable as ____________________ cable.

Question 41

Explain why two-wire Romex cable cannot be stapled on edge.

Question 42

Explain why you do not overtighten the clamp of a metal cable connector when securing a cable to an electrical enclosure.

Question 43

Explain what a 'jug handle' is.