Deck 8: Netware Protocol, Routing, and Routing Techniques

Question 1

Which NetWare protocol works on layer 3- network layer-of the OSI model?

A)ipx
B)ncp
C)spx
D)netbios

Answer 1

ipx

Question 2

Which NetWare protocol provides link- state routing?

A)nlsp
B)rip
C)sap
D)ncp

Answer 2

nlsp

Question 3

As a system administrator, you want to debug IGRP but are worried that the "debug IP IGRP transaction" command will flood the console. What is the command that you should use?

A)debug ip igrp event
B)debug ip igrp-events
C)debug ip igrp summary
D)debug ip igrp events

Answer 3

debug ip igrp events

Question 4

0.0.0 router IGRP 109 network 172.68.7.0

A)it isolates networks 10.0.0.0 and 172.68.7.0
B)it loads igrp for networks 109 and 71
C)it disables rip
D)it disables all routing protocols

Question 5

As a system administrator, you need to set up one Ethernet interface on the Cisco router to allow for both sap and Novell-ether encapsulations. Which set of commands will accomplish this?

A)interface ethernet 0.1 ipx encapsulation novell-ether ipx network 9e interface ethernet 0.2 ipx network 6c
B)interface ethernet 0 ipx encapsulation novell-ether ipx network 9e interface ethernet 0 ipx encapsulation sap ipx network 6c
C)interface ethernet 0.1 ipx encapsulation novell-ether interface ethernet 0.2 ipx encapsulation sap
D)interface ethernet 0.1ipx encapsulation novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c

Question 6

What does the "IPX maximum-paths 2" command accomplish?

A)it enables load sharing on 2 paths if the paths are equal metric paths
B)it sets up routing to go to network 2
C)it is the default for cisco ipx load sharing
D)it enables load sharing on 2 paths if the paths are unequal metric paths

Question 7

You want to enable both arpa and snap encapsulation on one router interface. How do you do this?

A)the interface can handle multiple encapsulation types with no extra configuration
B)assign two network numbers, one for each encapsulation type
C)enable novell-ether to run multiple encapsulation types
D)both arpa and snap are enabled by default so you don't have to configure anything

Question 8

By default, Cisco routers forward GNS SAPs to remote networks.

Question 9

To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks?

A)each router builds its own sap table and forwards that every 60 seconds
B)each router assigns a service number and broadcasts that
C)saps aren't necessary with cisco routers
D)cisco routers filter out all saps

Question 10

Novell's implementation of RIP updates routing tables every------------- seconds.

A)60
B)90
C)10
D)30

Question 11

In Novell's use of RIP, there are two metrics used to make routing decisions. Select the correct metrics.

A)ticks & hops
B)hops & loops
C)loops & counts
D)counts & ticks

Question 12

The term that is used to place packet in its route to its destination is called                      

A)delayed
B)urgent
C)forwarding
D)delivering

Question 13

A second technique to reduce routing table and simplify searching process is called

A)network-specific method
B)network-specific motion
C)network-specific maintaining
D)network-specific membership

Question 14

Next-Hop Method is used to reduce contents of a                    

A)revolving table
B)rotating table
C)routing table
D)re-allocate table

Question 15

In Unicast routing, if instability is between three nodes, stability cannot be                  

A)stable
B)reversed
C)guaranteed
D)forward

Question 16

RPF stands for                      

A)reverse path forwarding
B)reverse path failure
C)reverse packet forwarding
D)reverse protocol failure

Question 17

LSP stands for                      

A)link stable packet
B)link state packet
C)link state protocol
D)link state path

Question 18

Protocol is a set of

A)formats
B)procedures
C)formats & procedures
D)none of the mentioned

Question 19

Several techniques can make size of routing table manageable and also handle issues such as                      

A)maturity
B)error reporting
C)tunneling
D)security

Question 20

Host-specific routing is used for purposes such as checking route or providing            

A)network measures
B)security measures
C)routing measures
D)delivery measures

Question 21

In Unicast Routing, Dijkstra algorithm creates a shortest path tree from a                  

A)graph
B)tree
C)network
D)link

Question 22

In Multicast Routing Protocol, flooding is used to broadcast packets but it creates

A)gaps
B)loops
C)holes
D)links

Question 23

The computation of the shortest path in OSPF is usually done by                          

A)bellman-ford algorithm
B)routing information protocol
C)dijkstra's algorithm
D)distance vector routing

Question 24

Which of the following is false with respect to the features of OSPF?

A)support for fixed-length subnetting by including the subnet mask in the routing message
B)more flexible link cost than can range from 1 to 65535
C)use of designated router
D)distribution of traffic over multiple paths that have equal cost to the destination

Question 25

In OSPF, which protocol is used to discover neighbour routers automatically?

A)link state protocol
B)error-correction protocol
C)routing information protocol
D)hello protocol