Question 1

Front-wheel-drive vehicles typically have ____________________ strut suspensions.

Accepted Answer

Macpherson

Question 2

A noisy joint will get quieter with the installation of a new boot and grease.

Accepted Answer

A noisy joint, such as a CV joint in a vehicle, indicates wear or damage. Simply adding a new boot and grease won't fix the underlying issue causing the noise; it may temporarily reduce the noise but won't solve the problem of the worn or damaged parts.

Question 3

The part MOST-Likely used to retain a fixed joint to the shaft is a(n):

Accepted Answer

An internal circlip is most likely used to retain a fixed joint to the shaft as it fits into a groove on the shaft, providing a secure hold that prevents lateral movement.

Question 4

A(n) ____ is located at the end of the fixed-type outer CV joint.

Accepted Answer

The stub shaft is a component located at the end of the fixed-type outer CV joint.

Question 5

While having a discussion, Technician A says that you should not use a regular hose clamp to replace a boot clamp. Technician B says that in a pinch, a nylon tie strap can be used for a day or two until a clamp can be purchased. Who is correct?

Accepted Answer

Technician A is correct because a regular hose clamp may not provide the even pressure needed for a boot clamp, potentially causing damage or leaks. Technician B is also correct because a nylon tie strap can serve as a temporary solution until a proper clamp is obtained.

Question 6

A(n) ____ is used to remove some types of splined inner joints.

Accepted Answer

A slide hammer is commonly used to remove splined inner joints from their shafts. The slide hammer features a weighted shaft that is slid back and forth within a tube to create an impact that can break the joint free from the shaft. The other options listed – halfshaft, slip yoke, and O-ring – do not pertain to the removal of splined inner joints.

Question 7

All of the following statements are true EXCEPT:

Accepted Answer

The statement that rebuilt halfshafts are usually available at about half the cost of CV joint repair is false. Rebuilt halfshafts typically cost more than just repairing the CV joint.

Question 8

A bad plunge joint will make a clunking sound when starting from a stop, during deceleration, or when braking.

Accepted Answer

This is because a bad plunge joint can cause vibration and movement in the drivetrain, which can result in clunking sounds during these driving situations.

Question 9

CV joints are lubed for life.

Accepted Answer

CV joints are typically sealed with grease inside a protective boot, designed to last the lifetime of the vehicle without needing additional lubrication.

Question 10

Noises coming from the front axle are not usually detected during a test drive.

Accepted Answer

Noises coming from the front axle can often be detected during a test drive, as they may indicate issues such as worn bearings or CV joints, which can produce audible sounds when the vehicle is in motion.

Question 11

____________________ rings are sometimes installed in a groove to locate or limit movement of a part on a shaft.

Accepted Answer

The answer of ____________________ rings are sometimes installed in a...

Question 12

Which of the following is LEAST-Likely a type of boot clamp?

Accepted Answer

Torque clamp is not typically categorized as a type of boot clamp. Boot clamps, such as bridge-type, earless, and universal clamps, are specifically designed for securing CV boots or similar applications, whereas "torque clamp" does not refer to a specific style of clamp used for this purpose.

Question 13

On some vehicles it is easier to move the hub away from the stub shaft if the ____________________ is removed first.

Accepted Answer

The answer of On some vehicles it is easier to...

Question 14

The part that MOST-Likely rides in a groove in the axle and fits into a corresponding groove inside the inner race is the:

Accepted Answer

The circlip is designed to fit into a groove in the axle and also fits into a corresponding groove inside the inner race, securing components in place.

Question 15

All of the following parts are contained in a CV joint boot kit EXCEPT:

Accepted Answer

The CV joint boot kit contains a boot, a circlip, and a clamp to replace or repair the CV joint boot. However, it does not typically include a nut, as this component is typically reused during the repair process.

Question 16

When a boot fails, its grease leaks out.

Accepted Answer

When a boot fails, its grease can leak out, especially if it is a CV boot that is designed to hold grease to lubricate the joint.

Question 17

Some vehicles have a conventional ball joint with a tapered connection. Others use a(n) ____________________-type ball joint connection.

Accepted Answer

The answer of Some vehicles have a conventional ball joint...

Question 18

A(n) ____________________ is used when there is a problem with the axle clearing other parts.

Accepted Answer

The answer of A(n) ____________________ is used when there is...

Question 19

While having a discussion, Technician A says that the estimated life of a joint is eight hours without lubricant. Technician B says that the estimated life is forty-eight hours. Who is correct?

Accepted Answer

The answer of While having a discussion, Technician A says...

Question 20

Which of the following is LEAST-Likely a type of retaining ring?

Accepted Answer

Joint ring is not a common type of retaining ring. Circle clip, external snap ring, and internal snap ring are all common types of retaining rings.

Quiz 78: Front-Wheel-Drive Transaxle and Cv Joint Service