Question 1

Very thin features, less than .06 in. (4 mm) thick, can be shown on the print ____________ section lines.

Accepted Answer

The answer of Very thin features, less than .06 in....

Question 2

____________________ or _________________________ are used to describe in interior portions of an object that are otherwise difficult to visualize.

Accepted Answer

The answer of ____________________ or _________________________ are used to describe...

Question 3

Sectional views are also called ________, and the process of creating sections is referred to as _______.

Accepted Answer

Sectional views are also called sections, and the process of creating sections is referred to as sectioning. None of the other options are correct terminology for sectional views.

Question 4

If there are enough sectional views on a drawing to use up all of the letters of the alphabet, then _______ letters are used to label the cutting plane lines and related views, such as ___________.

Accepted Answer

The answer of If there are enough sectional views on...

Question 5

____________________ are used to represent specific material section line symbols in the sectional view.

Accepted Answer

The answer of ____________________ are used to represent specific material...

Question 6

The cutting plane of an ___________________ is offset through staggered interior features of an object to show those features in section as if they were in the same plane.

Accepted Answer

The answer of The cutting plane of an ___________________ is...

Question 7

The cutting plane line for an offset section is generally shown using ________ where it offsets through the staggered features.

Accepted Answer

The answer of The cutting plane line for an offset...

Question 8

A _________________________ is used when a symmetrical object requires sectioning and one quarter of the object is removed to create the section.

Accepted Answer

The answer of A _________________________ is used when a symmetrical...

Question 9

The letters _______________ are not used for sectional view identification.

Accepted Answer

The answer of The letters _______________ are not used for...

Question 10

_____________ can be shown when a long object of constant shape throughout its length requires shortening to fit on a sheet or for creating a partial view.

Accepted Answer

The answer of _____________ can be shown when a long...

Question 11

The ________ cutting-plane line staggers to pass through offset features of an object, and normally the change in direction of the cutting-plane line is less than 90°.

Accepted Answer

The answer of The ________ cutting-plane line staggers to pass...

Question 12

The sectional view is created by placing an imaginary _________________________ through the object cutting away the area to be exposed.

Accepted Answer

The answer of The sectional view is created by placing...

Question 13

An alternate technique for placing the cutting-plane lines is called the ________________. When using this method for identifying sections, arrowheads point toward each end of the cutting-plane line and the section identification letters are placed at the ends of the cutting plane line. The view title is placed above the removed section.

Accepted Answer

The answer of An alternate technique for placing the cutting-plane...

Question 14

Multiple removed sections are generally arranged on the sheet in ________________ from left to right and top to bottom.

Accepted Answer

The answer of Multiple removed sections are generally arranged on...

Question 15

The cutting-plane line is a thick line representing the cutting plane and can be drawn using:

Accepted Answer

The cutting-plane line is typically represented by alternating long and two short dashes.

Question 16

A _________________________ is drawn when the cutting plane extends completely through the object, usually along a center plane.

Accepted Answer

The answer of A _________________________ is drawn when the cutting...

Question 17

An assembly section of adjacent parts of different materials has ____.

Accepted Answer

The answer of An assembly section of adjacent parts of...

Question 18

An object has a very small internal portion dimensioned on a print. Given only this information, which of the following is a viable option for dimensioning the small portion of the object?

Accepted Answer

The answer of An object has a very small internal...

Question 19

A _______________ can be shown when a feature has a constant shape throughout the length that cannot be shown in an external view, and the types of feature shapes that are common with are extrusions, spokes, beams, and arms.

Accepted Answer

The answer of A _______________ can be shown when a...

Question 20

General section lines ____.

Accepted Answer

General section lines are evenly spaced and also serve as the coded section lines for cast iron, making both statements A and B correct.

Quiz 10: Reading Sections, Revolutions, and Conventional Breaks