Question 1

The space between two gear teeth in contact is called:
A)runout
B)backlash
C)Both A and B
D)Neither A nor B

Accepted Answer

Backlash is the correct term for the space between two gear teeth in contact. It is a necessary clearance or the amount of lost motion due to gaps between the gear teeth, allowing for smooth operation. Runout, on the other hand, refers to the deviation of a mechanical part's surface from its ideal form.

Question 2

The flow of electrons is called ___________, or current flow.

Accepted Answer

amperage

Question 3

When an electrical circuit is constructed, a resistance, called a ____________________, is placed in the path of the electrons.

Accepted Answer

load

Question 4

A dial caliper can measure a component's:
A)depth
B)inside size
C)outside size
D)All of the above

Accepted Answer

A dial caliper is a versatile tool that can measure depth, inside size, and outside size of a component.

Question 5

A thank you note should be sent to the interviewer within _____ of an interview.
A)a week
B)two days
C)two hours
D)five days

Accepted Answer

Sending a thank you note within two days of an interview is considered prompt and shows appreciation for the interviewer's time while keeping you fresh in their mind.

Question 6

Personal digital portfolios are used specifically to provide information on a résumé and to show evidence of learning, certifications, and examples of work performed.

Accepted Answer

The answer of Personal digital portfolios are used specifically to...

Question 7

Technician A says getting ready for an interview should include learning about the company.Technician B says getting ready for an interview should include making a list of questions that might be asked.Who is correct?
A)A only
B)B only
C)both A and B
D)neither A nor B

Accepted Answer

Both technicians are correct. Technician A is correct in that it's important to research and learn about the company you are interviewing with. This can include understanding their products, services, mission statement, and any recent news or developments. Technician B is correct in that preparing for potential questions that may be asked during the interview can help alleviate nerves and better articulate your qualifications and experience. It's also important to have questions prepared to ask the interviewer to show your interest in the company and position.

Question 8

A straightedge and feeler gauge are used to measure _____.
A)clearances
B)warpage
C)runnout
D)endplay

Accepted Answer

A straightedge and feeler gauge are primarily used to measure warpage, especially on flat surfaces such as cylinder heads or engine blocks, to ensure they meet flatness specifications.

Question 9

Any change in the bonds between atoms constitutes a (an) ___________ reaction.

Accepted Answer

The answer of Any change in the bonds between atoms...

Question 10

What type of energy is developed at the engine crankshaft?
A)Electrical
B)Mechanical
C)Thermal
D)Chemical

Accepted Answer

The engine crankshaft converts the reciprocating motion of the pistons into rotational motion, which is a form of mechanical energy.

Question 11

The amount of side-to-side variation of an object is called ___________ runout.

Accepted Answer

The answer of The amount of side-to-side variation of an...

Question 12

Metric measurements are all based on units of one.

Accepted Answer

Metric measurements are based on units of ten, not one. The metric system uses powers of ten for its base units, such as meters, liters, and grams.

Question 13

With _______ measurement, technicians use tools such as micrometers, dial calipers, and dial indicators.
A)metric
B)linear
C)precision
D)volume

Accepted Answer

Precision measurement involves the use of tools like micrometers, dial calipers, and dial indicators to obtain highly accurate measurements.

Question 14

A technician turns in 50 hours of work in a 40-hour workweek.He is being paid $20 per flat rate.How much is he actually making per hour?
A)$20 per hour
B)$50 per hour
C)$25 per hour
D)none of these answers is correct

Accepted Answer

The technician worked 10 hours overtime (50-40=10). The overtime pay for flat rate workers is usually calculated at 1.5 times the regular hourly rate. So, the technician actually worked (40 hours + 10 hours OT x 1.5) = 55 hours. The flat rate of $20 per hour is now equivalent to ($20/1.5) = $13.33 per hour. Thus, the technician is actually making ($13.33 x 55)=$733.15 per week. So, the correct answer is C) $25 per hour (approximate calculation).

Question 15

Micrometers are used to measure brake rotor thickness down to 0.01 mm.

Accepted Answer

Micrometers are precision measuring tools capable of measuring thicknesses down to 0.01 mm, making them suitable for applications like measuring brake rotor thickness.

Question 16

The first impression you make to a prospective employer is the clothing you wear to the job interview.

Accepted Answer

The first impression to a prospective employer encompasses not only clothing but also punctuality, body language, manners, and the way you communicate, among other factors.

Question 17

__________, a form of air pollution, is caused by chemical reactions between exhaust emissions and sunlight.

Accepted Answer

The answer of __________, a form of air pollution, is...

Question 18

The repair order (RO) serves as the record of tests, inspections, and findings by the technician once the vehicle is in the service bay.

Accepted Answer

The repair order (RO) documents all the tests, inspections, and findings conducted by the technician, serving as a comprehensive record of the service performed on the vehicle.

Question 19

What is the formula for calculating torque?
A)Force x area
B)Force x radius
C)Force x distance
D)Force x diameter

Accepted Answer

Torque is calculated as the force applied at a distance from the pivot point, hence the formula is Force x distance.

Question 20

What is the specific gravity of water?
A)1.0
B)10.0
C)5.0
D)1.2

Accepted Answer

The specific gravity of water is 1.0, which is used as a reference standard for comparing the density of other substances.

Quiz 4: Basic Technician Skills

The space between two gear teeth in contact is called:

The flow of electrons is called ___________, or current flow.

When an electrical circuit is constructed, a resistance, called a ____________________, is placed in the path of the electrons.

A dial caliper can measure a component's:

A thank you note should be sent to the interviewer within _____ of an interview.

Personal digital portfolios are used specifically to provide information on a résumé and to show evidence of learning, certifications, and examples of work performed.

Technician A says getting ready for an interview should include learning about the company.Technician B says getting ready for an interview should include making a list of questions that might be asked.Who is correct?

A straightedge and feeler gauge are used to measure _____.

Any change in the bonds between atoms constitutes a (an) ___________ reaction.

What type of energy is developed at the engine crankshaft?

The amount of side-to-side variation of an object is called ___________ runout.

Metric measurements are all based on units of one.

With _______ measurement, technicians use tools such as micrometers, dial calipers, and dial indicators.

A technician turns in 50 hours of work in a 40-hour workweek.He is being paid $20 per flat rate.How much is he actually making per hour?

Micrometers are used to measure brake rotor thickness down to 0.01 mm.

The first impression you make to a prospective employer is the clothing you wear to the job interview.

__________, a form of air pollution, is caused by chemical reactions between exhaust emissions and sunlight.

The repair order (RO) serves as the record of tests, inspections, and findings by the technician once the vehicle is in the service bay.

What is the formula for calculating torque?

What is the specific gravity of water?