Question 1

A customer has requested the storage integrator to assist in installation of a HPE 3PAR StoreServ 8200. As a best practice, what should be taken into consideration when deploying 3PAR Virtual Service Processor?

Accepted Answer

The answer of A customer has requested the storage integrator...

Question 2

Refer to the exhibit.  Which command can be used in the CLI console to set the static IP address and DNS server for an HPE StoreOnce device?

Accepted Answer

The answer of Refer to the exhibit.  Which command...

Question 3

Refer to the exhibit.  A customer wants to implement compression on an HPE 3PAR system and is concerned about potential bottlenecks on the CPU. Which CLI command can be used to display the CPU utilization and create a performance baseline?

Accepted Answer

The answer of Refer to the exhibit.  A customer...

Question 4

Your customer needs to extend their storage SAN environment without the additional workload of manually creating zones for every new host or storage device. What will allow the customer to move from creating zones manually to having zones created automatically?

Accepted Answer

The answer of Your customer needs to extend their storage...

Question 5

An HPE StoreVirtual 3200 solution specifies 802.3ad (LACP) bonding is required for the network interfaces. What must be considered when implementing this solution?

Accepted Answer

HPE StoreVirtual 3200 provides three options for the teaming/bonding of the network ports on each storage controller-Active-Passive, Link Aggregation Dynamic Mode (LACP), or Adaptive Load Balancing (ALB) bonding. The simplest solution, the Active-Passive bonding, utilizes only one of the available network ports per controller. The most complex solution, the LACP (802.3ad) bonding, delivers bandwidth aggregation and redundancy across both controller network ports but requires additional switch configurations such as IRF trunking. The preferred and recommended bonding mode is ALB, where the network ports may be connected to different switches, therefore, support switch failover.

Question 6

A customer wants to expand their SAN environment, which is based on B-series FC switches. They have a virtualized environment and two HPE 3PAR StoreServ arrays. Which tools can be used by the Integrator to check the health of the SAN environment before starting the expansion and after finishing? (Choose two.)

Accepted Answer

The answer of A customer wants to expand their SAN...

Question 7

A storage integrator is installing an HPE MSA 2042 into a remote location as a part of warehouse automation solution. The site has no IT staff and warehouse employees will not be granted access to the location where the MSA will be installed. The customer is concerned about the inability to control individual AC power outlets connected to the MSA. Which HPE power delivery equipment can be added to the solution to address these requirements? (Choose two.)

Accepted Answer

The answer of A storage integrator is installing an HPE...

Question 8

Refer to the exhibit.  A storage integrator is deploying an HPE StoreOnce VSA. Which command can be used to find available storage capacity before it can be added in the StoreOnce console?

Accepted Answer

The answer of Refer to the exhibit.  A storage...

Question 9

A storage integrator is planning the implementation of a single HPE StoreOnce 3100. How many power cords are required to be connected to PDU from this storage system, when power supply kit was ordered?

Accepted Answer

The HPE StoreOnce 3100 typically comes with dual power supplies for redundancy, requiring two power cords to be connected to the PDU.

Question 10

A customer has an HPE 3PAR StoreServ 8000 system with three tiers of SSDs, SAS HDDs, and NL SAS. They are using Adaptive Flash Cache (AFC) and Adaptive Optimization (AO) across all three tiers. They want to implement a new virtual desktop infrastructure and want to use deduplication on the array for this workload. The integrator is in the process of implementing additional SSD drives to prepare the array for the new workload. What must the integrator do to implement this solution?

Accepted Answer

To implement deduplication, the integrator should configure a new Common Provisioning Group (CPG) for the SSD tier, as deduplication is typically applied at the CPG level.

Question 11

A customer has the following components installed and running: - HPE 3PAR StoreServ 8400 with two nodes - three SFF drive shelves - FC-based host connections - a mixture of SSDs and SAS HDDs The task is to expand the solution with two nodes and another three SFF drive shelves, as well as SSDs and SAS HDDs. What must be checked at the customer site before beginning the installation?

Accepted Answer

The answer of A customer has the following components installed...

Question 12

A storage integrator is handing over an installed HPE StoreOnce solution to the customer and demonstrates the default usernames and passwords for the StoreOnce GUI. The storage administrator is interested in creating another local administrator account. How can the storage administrator create an administrator account?

Accepted Answer

The answer of A storage integrator is handing over an...

Question 13

The system administrator created a volume on an HPE MSA 2042 storage solution. The storage administrator is complaining that the Storage Management Utility (SMU) displays allocated space, but there is no data on the disk yet and the volume is empty. How can the storage integrator fix the issue?

Accepted Answer

The answer of The system administrator created a volume on...

Question 14

A storage integrator is implementing an HPE 3PAR StoreServ system and connecting several storage volumes to a customer's VMware farm. During the implementation, the customer reveals that their legacy backup solution for protecting virtual machines does not provide a satisfactory RTO (recovery time objective). A recent implementation of new StoreOnce appliances did not fully solve the problem. Which HPE solution could the integrator demonstrate to address the customers RTO concerns?

Accepted Answer

HPE Recovery Manager Central for VMware is designed to provide efficient backup and recovery solutions specifically for VMware environments, addressing RTO concerns by integrating with HPE storage solutions like 3PAR and StoreOnce.

Question 15

After installing the HPE StoreOnce VSA into the VM environment, where can the version number of the software be checked?

Accepted Answer

The version number of the software can be checked in the install log file.

Question 16

What does DWPD (drive writes per day) for an SSD indicate?

Accepted Answer

DWPD (drive writes per day) indicates the maximum number of times the entire capacity of an SSD can be written to per day over a five-year period.

Question 17

A storage integrator is handing over an installed HPE 3PAR storage system to a customer. The customer wants the original license key of the system for setlicense command that is used to prevent the system from prompting for confirmation of new license key. Which of the following command shows original license key?

Accepted Answer

The command "showlicense -raw" is used to display the original license key on an HPE 3PAR storage system.

Question 18

A storage integrator is handing over an installed HPE StoreOnce solution to the customer and demonstrates that the system is property configured. Which CLI command can be used to run an appliance self-test?

Accepted Answer

The command "system confidencechecker runtest all" is used to run a comprehensive self-test on the HPE StoreOnce appliance to ensure it is properly configured.

Question 19

A storage administrator has deployed a Windows 2012 R2 server which needs to have a virtual volume exported from an HPE StoreServ 8200. After zoning the host to storage and installing the HPE 3PAR Host Explorer on the server, the administrator is not seeing the server name in SSMC host list when creating a host object. What are two valid options to correct the issue? (Choose two.)

Accepted Answer

Enable host explorer discovery from the HPE 3PAR CLI and execute tpdhostagent push to correct the issue.

Question 20

In which areas in SSMC can a 3PAR virtual domain membership be selected? (Choose two.)

Accepted Answer

The answer of In which areas in SSMC can a...

Exam 1: Designing Multi-Site HPE Storage Solutions