Question 1

The WLC port that is used to connect to a peer controller for high availability (HA) operation is known as what?
A) Service port
B) Redundancy port
C) Console port
D) Distribution system port

Accepted Answer

B) The WLC port that is to connect to a peer controller for high availability (HA) operation is known as the redundancy port.

Question 2

The WLC port that is used for all normal AP and management traffic, and usually connects to a switch port in 802.1Q trunk mode is known as what?
A) Service port
B) Redundancy port
C) Console port
D) Distribution system port

Accepted Answer

D) A distribution system port is sed for all normal AP and management traffic and usually connects to a switch port in 802.1Q trunk mode.

Question 3

Which WLC port is used for out-of-band management, system recovery, and initial boot functions and always connects to a switch port in access mode?
A) Service port
B) Redundancy port
C) Console port
D) Distribution system port

Accepted Answer

A) A service port is used for out-of-band management, system recovery, and initial boot functions and always connects to a switch port in access mode.

Question 4

Which WLC port is an asynchronous connection to a terminal emulator that can be used for out-of-band management, system recover, and initial boot functions?
A) Service port
B) Redundancy port
C) Console port
D) Distribution port

Accepted Answer

A console port is an asynchronous connection to a terminal emulator that can be used for out-of-band management, system recover, and initial boot functions.

Question 5

Which interface is used for normal management traffic, such as RADIUS user authentication, WLC-to-WLC communication, web-based and SSH sessions, as well as used to terminate CAPWAP tunnels between the controller and it's AP?
A) Management interface
B) Virtual interface
C) Service port interface
D) Dynamic interface

Accepted Answer

A) The management interface is used for normal management traffic, such as RADIUS user authentication, WLC-to-WLC communication, web-based and SSH sessions, SNMP, Network Time Protocol (NTP), syslog and is also used to terminate CAPWAP tunnels between the controller and it's AP.

Question 6

When connecting a VLAN to a WLAN, which interface is used?
A) Management interface
B) Virtual interface
C) Service port interface
D) Dynamic interface

Accepted Answer

D) A dynamic interface is used to connect a VLAN to WLAN.

Question 7

Fill in the blanks: Cisco controllers support a maximum of ______ WLANs, but only ____ of them can be actively configured on an AP.
A) 16, 5
B) 512, 16
C) 100, 50
D) 100, 5

Accepted Answer

Cisco controllers support a maximum of 512 WLANs, but only 16 of them can be actively configured on an AP.

Question 8

By default, on a Cisco WLC, the Quality of Service (QoS) is set to which of the following?
A) Platinum
B) Gold
C) Silver
D) Bronze

Accepted Answer

C) By default, Cisco WLC will consider all frames in the WLAN to be normal data and handle it in a best effort manner. The "best effort" category is known as the Silver category.

Question 9

If you wanted to classify all frames in your WLAN as "video" for QoS, which of the following should you select from the QoS drop-down menu?
A) Platinum
B) Gold
C) Silver
D) Bronze

Accepted Answer

B) To classify all frames as video frames in the QoS drop-down, you would select Gold.

Question 10

On what configuration page of the Cisco WLC would you be able to configure a Wi-Fi Multimedia (WMM) policy?
A) Advanced
B) General
C) Security
D) QoS

Accepted Answer

D) On the QoS page you may configure items such as the Wi-Fi Multimedia (WMM) policy, call admission control (CAC) policies, and bandwidth parameters.

Question 11

Which of the following is not a method for accessing a Cisco WLC?
A) HTTPS
B) HTTP
C) FTP
D) SSH

Accepted Answer

HTTP, HTTPS, and SSH are all valid methods of accessing a Cisco WLC; FTP is not.

Question 12

When using a Cisco WLC, client sessions with the WLAN are set to how many seconds by default?
A) 600
B) 900
C) 1800
D) 3600

Accepted Answer

When using a Cisco WLC, client sessions with the WLAN are set to 1800 seconds (30 min) by default, but this can be changed on the Advanced Settings page.

Quiz 29: Building a Wireless Lan

The WLC port that is used to connect to a peer controller for high availability (HA) operation is known as what?

The WLC port that is used for all normal AP and management traffic, and usually connects to a switch port in 802.1Q trunk mode is known as what?

Which WLC port is used for out-of-band management, system recovery, and initial boot functions and always connects to a switch port in access mode?

Which WLC port is an asynchronous connection to a terminal emulator that can be used for out-of-band management, system recover, and initial boot functions?

Which interface is used for normal management traffic, such as RADIUS user authentication, WLC-to-WLC communication, web-based and SSH sessions, as well as used to terminate CAPWAP tunnels between the controller and it's AP?

When connecting a VLAN to a WLAN, which interface is used?

Fill in the blanks: Cisco controllers support a maximum of __ WLANs, but only of them can be actively configured on an AP.

By default, on a Cisco WLC, the Quality of Service (QoS) is set to which of the following?

If you wanted to classify all frames in your WLAN as "video" for QoS, which of the following should you select from the QoS drop-down menu?

On what configuration page of the Cisco WLC would you be able to configure a Wi-Fi Multimedia (WMM) policy?

Which of the following is not a method for accessing a Cisco WLC?

When using a Cisco WLC, client sessions with the WLAN are set to how many seconds by default?